Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Fortinet
  4. 1000B
  5. Merkblatt

Fortinet 1000B Merkblatt

Download
Seite von 2
Port Information
Port 1
IP:
____.____.____.____
Netmask:
____.____.____.____
Port 2
IP:
____.____.____.____
Netmask:
____.____.____.____
Port 3
IP:
____.____.____.____
Netmask:
____.____.____.____
Port 4
IP:
____.____.____.____
Netmask:
____.____.____.____
The internal interface IP address and netmask must be valid for the internal network.
General settings
Administrator password: 
Network Settings: 
Default Gateway: 
____.____.____.____
Primary DNS Server:
____.____.____.____
Secondary DNS Server:
____.____.____.____
Factory default settings
NAT/Route mode
Transparent mode
Port 1 interface
192.168.1.99
Management IP
0.0.0.0
Port 2 interface
0.0.0.0
Administrative account settings
Port 3 interface
0.0.0.0
User name
admin
Port 4 interface
0.0.0.0
Password
(none)
To reset the FortiAnalyzer unit to the factory defaults, in the CLI type the command 
 
execute factory reset
Collecting Information
Configuring
Web-based Manager
Use the following procedure to connect to the web-based manager for the first time. Configu-
ration changes made with the web-based manager are effective immediately without reset-
ting the FortiAnalyzer unit or interrupting service.
To connect to the web-based manager 
Connect the Port 1 interface of the FortiAnalyzer unit to Ethernet port of the manage-
ment computer. 
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through 
Ethernet cables to connect the devices through a hub or switch. 
Configure the management computer to be on the same subnet as the FortiAnalyzer 
Port 1 interface. 
To do this, change the IP address of the management computer to 192.168.1.2 and the 
netmask to 255.255.255.0.
To access the FortiAnalyzer web-based manager, in your browser, go to 
https://192.168.1.99 (remember to include the “s” in https://). 
Type 
admin in the Name field and select Login. 
After connecting to the Web-based manager, you can configure the FortiAnalyzer unit IP ad-
dress, DNS server IP address, and default gateway to connect the FortiAnalyzer unit to the 
network. 
To configure interfaces 
Go to 
System > Network > Interface.
Select the edit icon for each interface to configure.
Set the IP address and netmask for the interface.
Select OK.
To configure the Primary and Secondary DNS server IP addresses 
Go to 
System > Network > DNS, enter the Primary and Secondary DNS IP addresses 
select Apply.
To configure a Default Gateway 
Go to 
System > Network > Routing and select Create New.
Set Gateway to the Default Gateway IP address and select OK.
1.
2.
3.
4.
1.
2.
3.
4.
1.
1.
2.
Command Line Interface
The FortiAnalyzer-1000B has serial port. Use the null modem cable to connect it to your 
management computer.
To connect to the FortiAnalyzer unit 
Use a null modem cable to connect the FortiAnalyzer serial port to the management 
computer serial port. 
Start a terminal emulation program (such as HyperTerminal) on the management com-
puter. Use these settings: Baud Rate 9600, Data bits 8, Parity None, Stop bits 1, Flow 
Control None.
At the login: prompt, type 
admin and press Enter twice. 
(The login prompt is preceded by the server default host name.)
After connecting to the CLI, you can configure the FortiAnalyzer unit IP address, DNS server 
IP address, and default gateway to connect the FortiAnalyzer unit to the network.
 
To configure the FortiAnalyzer unit using the CLI 
Set the IP address and netmask of the Port1 interface. 
config system interface
    edit port1 
         set ip <intf_ip>/<netmask_ip>
end
Configure the primary and secondary DNS server IP addresses.
config system dns
    set primary <dns-server_ip>
    set secondary <dns-server_ip>
end
Configure the default gateway.
config system route
    edit 1
        set device <interface> 
        set dst <destination_ip> 
        set gateway <gateway_ip>
end
1.
2.
3.
1.
3.
4.
Adding an administration password
By default, the admin user does not have a password. To restrict access to the FortiAnalyzer 
unit management account, add password for the admin user account.
To add the admin user account password 
Go to 
System > Admin.
For the admin user, select the Change Password icon.
Enter a new password in the New Password box.
Reenter the password to Confirm Password box.
Select OK.
1.
2.
3.
4.
5.
Adding an administration password using the CLI
To add an administration password in the CLI enter the following commands:
config system admin
edit admin
set password <password>
end
Shutting down the FortiAnalyzer unit
When powering off the FortiAnalyzer unit, always shut down the unit using the following pro-
cedures before disconnecting the power supply. Not following this procedure can increase 
the risk of damaging the FortiAnalyzer hard disk.
To power off the FortiAnalyzer unit 
Go to 
System > Dashboard.
In the System Operation list, select Shut Down.
Select Go.
Once the indicates the shut down procedure has completed, disconnect the 
FortiAnalyzer unit from the power source.
Shutting down the FortiAnalyzer unit using the CLI
Enter the following command at the prompt:
execute shutdown
1.
2.
3.
4.