Sony HDS-X5800 Benutzerhandbuch
1-31 (E)
HDS-X5800
1-11. Setting the On-Board Switches and Description of LEDs
ON
1
2
3
4
5
6
7
8
Factory setting
( indicates the switch lever position.)
( indicates the switch lever position.)
BIT5 to BIT8 : Bit rate manual setting switch
BIT5 : Bit rate setting-1
BIT6 : Bit rate setting-2
BIT7 : Bit rate setting-3
BIT8 : Manual setting ON/OFF
BIT6 : Bit rate setting-2
BIT7 : Bit rate setting-3
BIT8 : Manual setting ON/OFF
Bit rate of all of the 34 channels are set at once.
Bit rate
BIT5
BIT6
BIT7
BIT8
Automatic setting
_
_
_
OFF
143 Mbps
OFF
OFF
OFF
ON
177 Mbps
ON
OFF
OFF
ON
270 Mbps
OFF
ON
OFF
ON
360 Mbps
ON
ON
OFF
ON
540 Mbps
OFF
OFF
ON
ON
1483.5/1485 Mbps
ON
OFF
ON
ON
_ : Don’t care.
m
. Set BIT8 to OFF (bit rate automatic setting mode) during
. Set BIT8 to OFF (bit rate automatic setting mode) during
normal operation.
. Manual setting of the bit rate is set to all of the 34
channels at once. It cannot be set individually for each
channel.
channel.
S3102 (D-7) : Re-clocker IC setting switch 2
8-pin DIP switch
8-pin DIP switch
BIT1 to BIT4 : Signal output slope setting switch
other than the standard specification
BIT1 : Setting OUTPUT1 through OUTPUT8
BIT2 : Setting OUTPUT9 through OUTPUT17
BIT3 : Setting OUTPUT18 through OUTPUT25
BIT4 : Setting OUTPUT26 through OUTPUT34
BIT2 : Setting OUTPUT9 through OUTPUT17
BIT3 : Setting OUTPUT18 through OUTPUT25
BIT4 : Setting OUTPUT26 through OUTPUT34
Used to set slope of the output signal in units of 8 output
channels or 9 output channels when handling the signals
other than the SMPTE specification bit rate (143 Mbps,
177 Mbps, 270 Mbps, 360 Mbps, 540 Mbps, 1483.5 Mbps
and 1485 Mbps) and the signals other than the DVB-ASI
signal (270 Mbps).
ON : SMPTE292M specification output slope
OFF : SMPTE259M specification output slope
m
. In the case of the SMPTE specification bit rate signal
channels or 9 output channels when handling the signals
other than the SMPTE specification bit rate (143 Mbps,
177 Mbps, 270 Mbps, 360 Mbps, 540 Mbps, 1483.5 Mbps
and 1485 Mbps) and the signals other than the DVB-ASI
signal (270 Mbps).
ON : SMPTE292M specification output slope
OFF : SMPTE259M specification output slope
m
. In the case of the SMPTE specification bit rate signal
and the DVB-ASI signal (270 Mbps), slope of output
signal is automatically set so that setting of this becomes
invalid.
signal is automatically set so that setting of this becomes
invalid.
<Automatic setting value>
1483.5/1485 Mbps :
1483.5/1485 Mbps :
SMPTE292M
specification output
slope
specification output
slope
Other than 1483.5/1485 Mbps : SMPTE259M
specification output
slope
slope
. This switch setting is valid only when the output board is
HKS-5860M.
If the output board is HKS-5860SD, slope of output
signal is fixed to the SMPTE259M specification output
slope and this switch setting becomes invalid.
If the output board is HKS-5860SD, slope of output
signal is fixed to the SMPTE259M specification output
slope and this switch setting becomes invalid.