Infocus C250W Benutzerhandbuch
12
Shutting down the projector
Turning off the projector
To turn off the projector, press the Power button and verify that you want to
turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks amber for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights amber and the fans stop. Unplug the power cable to completely
power off the projector.
turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks amber for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights amber and the fans stop. Unplug the power cable to completely
power off the projector.
Power Save
The projector has a Power Save feature that automatically turns the lamp off
after no signal is detected for 20 minutes. After 10 additional minutes with
no signal, the projector powers down. If an active signal is received before
the projector powers down, the image is displayed. You must press the
Power
after no signal is detected for 20 minutes. After 10 additional minutes with
no signal, the projector powers down. If an active signal is received before
the projector powers down, the image is displayed. You must press the
Power
button to display an image after 30 minutes have passed. When
Power Save is enabled, Screen Save is disabled. See page 29.
Screen Save
You can make a blank screen appear five minutes after no signal is detected
by turning on Screen Save in the Settings>System menu. See page 29.
There are six time options for the Screen Save feature. They range from five
minutes to 30 minutes with five minute intervals.
by turning on Screen Save in the Settings>System menu. See page 29.
There are six time options for the Screen Save feature. They range from five
minutes to 30 minutes with five minute intervals.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section
(page 21). If it does not, troubleshoot the setup.
(page 21). If it does not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
projector and can help you troubleshoot.
.
Table 1: Status indicator light behavior and meaning
Status Indicator Panel Symbols
Meaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and
the software is initializing.
The projector is on and initialized.
the software is initializing.
The projector is on and initialized.
The power button has been pressed twice
to turn the projector off and the fans are
running to cool the projector.
to turn the projector off and the fans are
running to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 19). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists
vents aren’t blocked (see page 19). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists
.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/service
to contact Service.
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/service
to contact Service.