Brother 4150CDN Merkblatt

(EU Only)

ENG

Version 0

 Note
The components included in the box may differ depending on your 

country.
We recommend that you save the original packaging.
If for any reason you must ship your machine, carefully repack 

the machine in the original packaging to avoid any damage during 

transit. The machine should be adequately insured with the 

carrier. How to repack the machine, see Shipment of the machine 

in the User’s Guide.
The interface cable is not a standard accessory. Buy the 

appropriate interface cable for the interface you want to use (USB 

or Network).

It is recommended to use a USB 2.0 (Type A/B) interface cable that 

is no longer than 2 meters (6 feet).
Network cable

Use a straight‑through Category5 (or greater) twisted‑pair cable for 

10BASE‑T or 100BASE‑TX Fast Ethernet Network.

•

•
•

•

Drum Unit 

(pre‑installed)

Waste Toner Box 

(pre‑installed)

Belt Unit 

(pre‑installed)

Starter Toner Cartridges 

(pre‑installed) 

(Black, Cyan, Magenta and Yellow)

Keep a minimum gap around the machine as shown in the illustration.

100 mm

(4.00 in.)

250 mm

(9.84 in.)

100 mm

(4.00 in.)

200 mm (7.87 in.)

 Remove the packing tape from the outside of the 

machine.

 Open the MP tray 

a

, and remove the plastic sheet 

b

 from the MP tray support, then close the MP tray.

 Pull the paper tray completely 

out of the machine.

 While pressing the green 

paper‑guide release lever 

a

, 

slide the paper guides to fit the 

paper size you are loading in the 

tray. Make sure that the guides 

are firmly in the slots.

 Fan the stack of paper well to 

avoid paper jams and misfeeds.

The machine has the following optional accessories. You can expand the capabilities of 

the machine by adding these items. For more information about the optional Lower Tray 

Unit and compatible SO‑DIMM Memory, visit us at http://solutions.brother.com/.

 For installing the SO‑DIMM Memory, see Installing extra memory in the User’s Guide.

Second lower paper tray unit can hold up to 

500 sheets of paper. When the tray is installed, 

the machine expands total input capacity up to 

800 sheets.

You can increase the memory 

by installing one SO‑DIMM 

(Small Outline Dual In‑line 

Memory Module).

 Connect the AC power cord to the machine and then 

connect it to an AC power outlet.

 Remove the label covering the machine’s power 

switch, and then switch the machine on.

 Press 

+ or − to choose 

General Setup.

Press 

OK.

 Press 

OK to choose 

Local Language.

 Press 

+ or − to choose your language.

Press 

OK.

When the time comes to replace consumable items, an error will be indicated by the LCD 

on the control panel. For more information about the consumables for your machine, visit 

us at http://www.brother.com/original/ or contact your local Brother reseller.

 For replacing the consumable items, see Replacing consumable items in the User’s Guide.

The Brother print server is equipped with a web server that allows 

you to monitor its status or change some of its configuration 

settings, using HTTP (Hyper Text Transfer Protocol).

 Note
The login name for the Administrator is ‘

admin’ (case sensitive) and 

the default password is ‘

access’.

We recommend Microsoft

®

 Internet Explorer

®

 6.0 (or greater) or 

Firefox 3.0 (or greater) for Windows

®

 and Safari 3.0 (or greater) for 

Macintosh. Please also make sure that JavaScript and Cookies are 

always enabled in whichever browser you use. To use a web browser, 

you will need to know the IP Address of the print server. The IP 

Address of the print server is listed on the Print Setting Page.

•

•

 Type 

http://machine_ip_address/ into your browser 

(where 

machine_ip_address is the IP Address or the print 

server name).

For example: http://192.168.1.2/

 See Web Based Management in the Network User’s Guide.



To reset all network settings of the print server to its 

factory default, follow the steps below.

 Press 

+ or − to choose 

Network.

Press 

OK.

 Press 

+ or − to choose 

Network Reset.

Press 

OK.

 Press 

+ to choose 

Reset.

 Press 

+ to choose 

Yes for reboot.

The machine will re‑start.

Before using this machine for the first time, read this Quick Setup 

Guide to setup and install your machine.

To view the Quick Setup Guide in other languages, please visit 

http://solutions.brother.com/.

Note: Not all models are available in all countries.

WARNING

WARNING indicates a potentially 

hazardous situation which, if not avoided, 

could result in death or serious injuries.

CAUTION

CAUTION indicates a potentially 

hazardous situation which, if not avoided, 

may result in minor or moderate injuries.

(HL‑4150CDN) In USA:

Please go to the Brother Solutions Center at 

download the other manuals.

  Remove the 4 orange 

packing pieces.

 Push the drum unit firmly 

back into the machine.

 Close the front cover of 

the machine.

 Press the front cover release 

button and open the front cover. 

Remove the silica gel pack 

a

.

DO NOT eat Silica Pack. Discard 

immediately.

 Hold the green handle of the 

drum unit and pull it out until it 

stops.

 Hold the orange packing 

material, and remove it.

 Put paper in the tray and make 

sure:

The paper is below the maximum 

paper mark (▼▼▼) 

a

.

Over filling the paper tray will 

cause paper jams.

The side to be printed on must 

be face down.

The paper guides touch the 

sides of the paper so it will feed 

properly.







 After the machine has finished warming up, the LCD will 

show 

Ready.

You can adjust the angle of the display by lifting it.

 Press 

Go. The machine will print a test page. Check 

that the test page has printed correctly.

This function will not be available after the first print job you 

send from your computer.

 Put the paper tray firmly 

back in the machine. Make 

sure that it is completely 

inserted into the machine.

 For more information about 

recommended paper, see 

print media in the User’s 

Guide.