Panasonic AW-SW350E Benutzerhandbuch
Q
Power Indicator [POWER]
Lights (green) when power is supplied to DC Power Input Terminal
Lights (green) when power is supplied to DC Power Input Terminal
L
and Power Switch
W
set to the ON position, and goes out when Power Switch
W
is set to the OFF position.
W
Power Switch [POWER ON/OFF]
Power is switched on and Power Indicator
Power is switched on and Power Indicator
Q
lights when this switch is set to the ON
position, provided that power is supplied to DC Power Input Terminal
L
. Power is
switched off and Power Indicator
Q
goes out when the switch is set to the OFF position.
9 (E)
ENGLISH
8 (E)
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■
TOP (CONTROL PANEL)
E
Wipe Pattern Selection Switches [WIPE PATTERN]
To select a wipe pattern after pressing Wipe Switch
To select a wipe pattern after pressing Wipe Switch
y
. One of the nine patterns can be
selected. The selected switch lights.
R
Setting Switch [SETTING]
This functions as the shift key for the wipe patterns. While it is held down, the Wipe Pattern
Selection Switches can select the functions described below. The functions are indicated
with blue characters.
This functions as the shift key for the wipe patterns. While it is held down, the Wipe Pattern
Selection Switches can select the functions described below. The functions are indicated
with blue characters.
SF0, SF1, SF2: These are used to set the three wipe softness levels.
The minimum softness level is set by SF0 (a hard key), and the maximum
softness level is set by SF2.
softness level is set by SF2.
MWR:
This makes it possible for the user to set the initial statuses of the panel
when the power is turned on.
First, set the statuses of the panel to be recorded. Once the setting has
been performed, keep pressing MWR while holding down the SETTING
switch until the nine switches go off. The recorded statuses will be
reproduced when the power is next turned on.
when the power is turned on.
First, set the statuses of the panel to be recorded. Once the setting has
been performed, keep pressing MWR while holding down the SETTING
switch until the nine switches go off. The recorded statuses will be
reproduced when the power is next turned on.
INT:
This is used to restore the initial settings which were established at the
factory.
Keep pressing INT while holding down the SETTING switch until the nine
switches go off. The same statuses as the factory setting statuses will be
established when the power is next turned on.
factory.
Keep pressing INT while holding down the SETTING switch until the nine
switches go off. The same statuses as the factory setting statuses will be
established when the power is next turned on.
FRZ:
This is used to set the freezing of the Video Input 5 signal to ON or OFF.
When FRZ is pressed while holding down the SETTING switch, the Video
Input 5 signal is frozen. While the signal is frozen, the FRZ
When FRZ is pressed while holding down the SETTING switch, the Video
Input 5 signal is frozen. While the signal is frozen, the FRZ
w
LED lights.
This signal can be used as the source of the VIDEO IN 5 signal.
✽
If the freeze function is used while the FS switch is in the OFF position,
only the Video Input 5 signal will be set to the FS ON status.
only the Video Input 5 signal will be set to the FS ON status.
POWER
INCOM
LEVEL
GEN-LOCK PHASE
WIPE PATTERN
TRANSITION TIME
KEY
SETTING
COLOR
WH1
S F 0
WH2
S F 1
WH3
AUTO TAKE
KEY AUTO
A
GAIN
SOURCE
I N 5
FMEM
KEY AUTO
CLIP
S F 2
YLW
MWR
CYN
I N T
GRN
F R Z
MGT
RED
BLE
N
N / R
R
I N V
H
SC
SC FINE
ON
OFF
A
1
2
3
4
5
FMEM
BLACK
MIX
FRZ
WIPE
AUTO TAKE
BAR
COLOR
B
B
Live Switcher AW-SW350
Even when the Power Switch is at the OFF position, some of the power supply circuits
are still operating. To turn off the power completely, set the external power adaptor to
OFF.
are still operating. To turn off the power completely, set the external power adaptor to
OFF.
Caution
SF0
MWR
SF1
INT
SF2
FRZ
INV