B&B Electronics EIR610 Series Merkblatt
EIR610 Series-5107qsg
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax 433-5104
www.bb-elec.com
orders@bb-elec.com
support@bb-elec.com
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
+353 91 792444 Fax +353 91 792445
www.bb-europe
.com orders@bb-europe.com support@bb-europe.com
Quick Start Guide
Elinx Managed Ethernet Switch
EIR610 Series
Items Included
1
2
3
LED Chart
Hardware Installation
Log into the Switch
5
4
o
Ethernet Switch
o
Console Cable (RS-232 RJ-45 to DB-9)
o
CD with Support Manual
o
This Quick Start Guide
o
Panel Mount Bracket
o
IP Address: 192.168.16.1
o
Subnet Mask: 255.255.255.0
o
Gateway: 192.168.16.254
o
User Name: root, Password: root
LED Status
Meaning
Green
The Switch is powered on
PWR
Off
The Switch is powered off
Green
Power Source 1 is available
PWR1
Off
Power Source 1 is unavailable
Green
Power Source 2 is available
PWR2
Off
Power source 2 is unavailable
Red
Power or Port failure
Fault
Off Normal
Operation
Green
The Switch is the master of a redundant
ring (X-Ring)
ring (X-Ring)
R.M
Off
The Switch is not the master of a
redundant ring.
redundant ring.
Green
SFP Port is linked
Blinking
Data is being transmitted or received
LINK/ACT
P7/9/10
*
SFP
Off
Not connected to the network
T Green Port
is
linked
T Blinking
Data is being transmitted or received
T Off
Not connected to the network
B Green
Operating at 1000M
Port
7/9/10*
RJ-45
B Off
Disconnected or below 1000M
T Green
Connected to the network
T Blinking
Data is being transmitted or received
T Off
Not connected to the network
B Yellow
Operating in full-duplex
B Blinking Data
collision
P1-6/8
*
B Off
Half-duplex or not connected
*Note
EIR610-3SFP: Ports 1-6 and 8 are 10/100 RJ-45, Ports
7, 9, and 10 are 100/1000 RJ-45 or SFP.
7, 9, and 10 are 100/1000 RJ-45 or SFP.
o
Record the switch’s MAC Address in the space
provided. The MAC Address is printed on the product
label. NOTE: Provide the MAC Address to your
Network Administrator. The Network Administrator
should provide an IP Address, Subnet Mask, and
Gateway.
provided. The MAC Address is printed on the product
label. NOTE: Provide the MAC Address to your
Network Administrator. The Network Administrator
should provide an IP Address, Subnet Mask, and
Gateway.
o
Select a mounting location and install with the attached
DIN rail clip or included panel mount kit.
DIN rail clip or included panel mount kit.
o
Connect power to the switch
o
12 to 48 VDC
o
Redundant inputs are available with fault
contacts.
contacts.
NOTE: The installation of an SFP Module disables
the associated RJ-45 Port.
the associated RJ-45 Port.
o
These instructions are for Web based management.
Refer to the User’s Manual for instructions concerning
console management.
Refer to the User’s Manual for instructions concerning
console management.
o
Connect a switch port to a stand alone PC. Change the
PC’s network IP Address to allow it to connect to the
switch (ex: 192.168.16.2). Use the default subnet mask
and gateway.
PC’s network IP Address to allow it to connect to the
switch (ex: 192.168.16.2). Use the default subnet mask
and gateway.
o
Launch the PC’s web browser and navigate to the
switch by typing the switch’s IP Address in the browser
address window.
switch by typing the switch’s IP Address in the browser
address window.
o
Navigate the web page by expanding the folders on the
left side of the web page.
left side of the web page.
Default Settings