Wagner SprayTech 0295001 Benutzerhandbuch

English

Cleaning the Spray Tip

1. Flush the gun with solvent immediately after the work is

completed.

2. Oil the sliding pins to prevent them from seizing up.

Should the spray tip become clogged,
reverse the spray tip with the lever and
pull the trigger. Once the obstruction
comes out of the spray tip, release the
trigger, reverse the spray tip back to the
spray pattern setting, and resume
spraying.

Do not attempt to clean the tip with your finger.
Do not use a needle or other sharp pointed instrument to
clean the tip. The hard tungsten carbide is brittle and can
be chipped.

Cleaning the Filter

Clean the filter with a brush dipped in solvent. Never poke the
filter with a sharp instrument.

Changing the Filter

1. Pull the trigger guard forward

so that it comes loose from
the handle.

2. Unscrew the handle from the

housing and remove the old
filter.

3. Slide the new filter, taper end

first, into the gun housing.

4. Replace the handle, washer

and spring. Screw the handle
into the housing until hand-
tight. Replace the trigger
guard.

Replacing the Valve Union Assembly

1. Unscrew the spray tip.
2. Lock the gun in the ON position and remove the diffuser

with a wrench

3. Unlock the gun.
4. Unscrew the nut

with a wrench
and remove the
retainer block.

5. Remove the

sliding pins with
care and store
them in a safe
place so they will
not be lost.

6. Drive the valve

union assembly
forward from the back of the retainer block. Use the
handle of a wooden hammer or similar soft tool to avoid
damaging the valve union assembly.

Gun Housing

Valve Union

Assembly

Sliding Pin

Retainer Block

Diffuser

Nut

NOTE: Replace the packing if the spray gun is

disassembled. Replace the sliding pins if they
are worn.

Gun Housing

Filter

Handle

WARNING

Accessories

Part No.

Description

0297xxx

RC Tip Assembly

0502xxx

Replacement Core, RC Tip

0297078

Tip Guard, RC Tip (11/16”)

0297070

Tip Guard, RC Tip (7/8”)

0291004

Hose, Whip End, 3' x 3/16"

0291003

Hose, Whip End, 5’ x 3/16”

0291002

Hose, Wireless, 25’ x 1/4"

0291000

Hose, Wireless, 50’ x 1/4"

0093896

Hose Connector, 1/4” x 1/4”M

0088154

Pressure Gauge

0152001

Power Roller Gun Attachment

0152308

9" Roller Cover, 3/8” Nap

0152307

9" Roller Cover, 1/2” Nap

0152309

9" Roller Cover, 3/4” Nap

0152310

9" Roller Cover, 1-1/4” Nap

0152235

12" Roller Cover, 1/2" Nap

0152236

12" Roller Cover, 3/8" Nap

0152237

12" Roller Cover, 3/4" Nap

0152238

12" Roller Cover, 1-1/4" Nap

0152700

Adapter, Power Roller Extension

0270145

G-10 Four Finger Airless Spray Gun (no tip)

0093930

Anti-Seize Compound

0152909

R-10 Telescoping Roller, 9", 3/8" Nap

0152900

R-10 Telescoping 12" Roller, 3/8" Nap

0502007

G-10 Four Finger Airless Spray Gun with 517
Reversible Tip

0502011

G-10 Two Finger Airless Spray Gun (no tip)

0502009

G-10 Two Finger Airless Spray Gun with 517
Reversible TIp

0270214

G-10 Four Finger Spray Pack with 50’ x 1/4”
airless hose

0502012

G-10 Two Finger Spray Pack with 50” x 1/4”
Airless Hose

Choosing the Correct Spray Gun Filter

Use the proper gun filter based on the type of material being
applied as shown below.

Part no.

Application

Filter
type

Mesh
number

Color of
Filter
body

0089960

Synthetic resin,
enamels, clean
varnishes, stains
azures

Extrafine

0.084 mm

red

0089959

Base coat enamels,
primer enamels,
fillers, marking paints,
textured enamels

Fine

0.140 mm

yellow

0089958

Emulsions,
latex paints,
acrylic paints

Medium

0.315 mm

white

0089957

Filler paints,
large area surfaces

Coarse

0.560 mm

green