Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Southbend
  4. SB1053F Turn-X
  5. Benutzerhandbuch

Southbend SB1053F Turn-X Benutzerhandbuch

Download
Seite von 140
Manual Insert
PHONE: (360) 734-1540  •  
www.southbendlathe.com
MODEL SB1053F TURN-X
14" X 40" GEARHEAD LATHE w/DRO
Copyright © December, 2013 by South Bend Lathe Co.  
WARNING: No portion of this manual may be reproduced without written approval. 
#TS16218   Printed in Taiwan
The Model SB1053F Lathe is the same machine as the Model SB1053 except for the following:
•  Added a 2-Axis Fagor Digital Readout (DRO).
Except for the differences noted in this insert, all other content in the Model SB1053 Owner’s Manual 
applies to this machine. Before operating your new lathe, you MUST read and understand this insert, 
the entire Model SB1053 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of 
injury when using this machine. Keep this insert for later reference.
If you have any further questions about this manual insert or the differences between the Model 
SB1053F and the Model SB1053, contact our Technical Support at (360) 734-1540 or email 
sales@southbendlathe.com.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1719
PSB1053F1719
DRO ASSEMBLY FAGOR 2-AXIS
1719-3 PSB1053F1719-3 DRO Y-AXIS SCALE FAGOR MKT-27
1719-1 PSB1053F1719-1 DRO DISPLAY FAGOR 20-iT
1801
PSB1053F1801 MACHINE ID LABEL
1719-2 PSB1053F1719-2 DRO X-AXIS SCALE FAGOR MKT-102
1811-1 PSB1053F1811-1 MODEL NUMBER LABEL
New & Changed Parts
1811-1
1801
1719
1719-1
1719-3
1719-2
MODEL SB1053F
Made in Taiwan to South Bend Specifications
MODEL SB1053F
14" x 40"
16-SPEED TOOLROOM
LATHE 7.5 HP w/DRO
MFG Date:
Serial No:
Compound Travel: 5.12"
Spindle Nose: D1-6 Camlock
Spindle Bore: 2.06"
Spindle Taper: MT#6
Tailstock Taper: MT#4
Tailstock Quill Travel: 6"
Weight: 2993 lbs.
WARNING!
!
Motor: 7.5 HP, 220V, 
           3-Ph, 60 Hz
Full-Load Current Rating: 20.3A
Swing Over Bed: 14.17"
Distance Between Centers: 40"
Swing Over Cross Slide: 8.42"
Swing Over Gap: 20.98"
Cross Slide Travel: 9"
®
To reduce the risk of serious personal injury while using this machine:
  1.  Read and understand owner’s manual before starting.
  2.  Always wear approved safety glasses AND a face shield.
  3.  Properly ground machine—connect to permanently grounded metal 
wiring system or an equipment-grounding conductor.
  4.  Tie back long hair, roll up sleeves, and DO NOT wear loose clothing, 
gloves, or jewelry.
  5.  Disconnect power before setting up, adjusting, or servicing.
  6.  Rotate workpiece by hand to ensure clearance before starting.
  7.  Test each new workpiece setup for safe rotation; start with slowest 
speed and stand to side of lathe until safe rotation verified.
  8.  Keep all guards and covers in place during operation. 
  9.  Change coolant regularly and avoid contact with skin.
 10.  Never  leave  chuck  key  in  chuck.
 11.  Never  leave  lathe  running  unattended.
 12.  DO  NOT  reverse  spindle  rotation  while  spindle  is  moving.
 13.  Properly  support  long  workpieces  with  an  appropriate  rest.
 14.  DO  NOT  expose  to  rain  or  use  in  wet  locations.
 15.  Prevent  unauthorized  use  by  children  or  untrained  users.
V1.12.13