Heath Zenith SL-5573 Benutzerhandbuch
598-1121-04
❒ Attach the canopy to the junction box (Apply silicon caulk
between canopy and junction box for a raintight seal). Keep the
fi xture horizontal (within +/- 4º) so the bulb inside is horizontal.
If the bulb is not horizontal, the bulb may darken or shatter
and fail prematurely.
fi xture horizontal (within +/- 4º) so the bulb inside is horizontal.
If the bulb is not horizontal, the bulb may darken or shatter
and fail prematurely.
❒ Loosen the side bolt connected to the arm to aim the fi xture up
and down.
❒ To avoid water entering fi xture, do not aim the fi xture above
the
the
horizon.
Bulb installation and relamping
Important: Use a clean glove or cloth when handling the new
bulb. Oil from your hand may cause the bulb to crack when the
fi xture heats up and result in premature failure. Use isopropyl
(rubbing) alcohol to clean the bulb if it is touched with your bare
hands.
bulb. Oil from your hand may cause the bulb to crack when the
fi xture heats up and result in premature failure. Use isopropyl
(rubbing) alcohol to clean the bulb if it is touched with your bare
hands.
❒ When relamping, turn power off and let the fi xture cool.
❒ Remove glass cover and remove the old bulb by pushing the bulb
❒ Remove glass cover and remove the old bulb by pushing the bulb
towards the right until the left side of the bulb is clear of the left
socket.
socket.
❒ To insert the new bulb push the bulb into the right socket so the
bulb is properly seated in the sockets.
❒ Re-install the glass cover.
❒ Reconnect the power.
❒ Reconnect the power.
Quartz Halogen Floodlight
Fixture Installation Instructions
To avoid Electrical Shock:
WIRING FIXTURE
(Product May Vary from Illustration)
White to White
Black to Black
Fixture ground to
junction box ground.
junction box ground.
Model SL-5571 - 150 Watts
Model SL-5573 - 300 Watts
Model SL-5575 - 500 Watts
Model SL-5573 - 300 Watts
Model SL-5575 - 500 Watts
The Heath
®
/Zenith Quartz Halogen Floodlight disperses light over a wide area, attaches to a standard junction box and is for use
with 120 VAC. Canopy and halogen lamp included.
FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.
To Avoid Fire or Burn Hazards:
• Allow fi xture to cool before touching. The bulb and the fi xture operate at high temperatures.
• Keep fi xture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).
• Use a lamp that does not exceed the ratings for your model. Maximum ratings are: SL-5571 - 150 Watts Max;
SL-5573 - 300 Watts Max; and SL-5575 - 500 Watts Max.
• Keep fi xture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).
• Use a lamp that does not exceed the ratings for your model. Maximum ratings are: SL-5571 - 150 Watts Max;
SL-5573 - 300 Watts Max; and SL-5575 - 500 Watts Max.
Canopy
No Service Parts Available for this Product
© 2007 HeathCo LLC
598-1121-04
WARNING: Turn power off at the circuit breaker or
fuse.
• Follow all warnings listed on fi xture.
• Grounding and installations must comply with local codes and
• Grounding and installations must comply with local codes and
the National Electric Code.
• This product should be mounted on a grounded junction box and
must be used with the canopy included.
• Permanently mount the fi xture to a building or pole.
SL-5571: Designed for wall or ceiling mount.
SL-5573 & 5575: Designed for wall mount only.
❒ Thread aiming arm into the enclosed canopy and tighten. Apply
SL-5571: Designed for wall or ceiling mount.
SL-5573 & 5575: Designed for wall mount only.
❒ Thread aiming arm into the enclosed canopy and tighten. Apply
silicon caulk to joint for a raintight seal. Seal the remaining holes
with the enclosed canopy plugs.
with the enclosed canopy plugs.
❒ Connect the lamp wires to the power source wiring. Secure with
wire connectors.