Roland Vs-880 Benutzerhandbuch

When a VS8F-1 effect expansion board is installed, a single
VS-880 now allows you to use two stereo effects.
Please read the VS8F-1 ownerÕs manual together with this
explanation.

■

One hundred preset patches have been added to the effect
patches. Refer to the included ÒPreset Patch List.Ó
Due to the increased number of preset patches, the patch
numbers have changed as follows.

Ver.1

V-XPANDED

Preset 001Ð100

Preset A00ÐA99

(newly added)

Preset B00ÐB99

User 001Ð100

User U00ÐU99

■

The following effect algorithms have been added.

Reverb 2 (p.23)
Space Chorus (p.24)
Lo-Fi Processor (p.25)
4-Band Parametric Equalizer (p.26)
10-Band Graphic Equalizer (p.27)
Hum Canceler (p.28)
Vocal Canceller (p.28)
Vocoder 2 (p.29)
Voice Transformer (p.30)
Mic Simulator (p.32)

●

This is a reverb that provides a gating function and a duck-
ing function. It can be used in either EFFECT-1 or EFFECT-
2. You can use two reverbs with different settings, or use it
in combination with a previous reverb.

Reverb

On, Off

Type

Room1, Room2, Hall1, Hall2, Plate

Time

0.1Ð10.0 sec

PreDLY

0Ð200 msec

Density

0Ð100

HPF

Thru, 20Ð2000 Hz

LPF

1.0Ð20.0 kHz, Thru

EFLevel

0Ð100

DiLevel

0Ð100

Gate

Off, On

Mode

Gate, Ducking

Thresh

0Ð100

Attack

1Ð100

Release

1Ð100

HoldTime

1Ð100

Reverb

Turn reverb on/off. When turned off, the following items
will not be displayed.

Type (Reverb Type)

Select the type of reverb.

Room1:

Normal room reverb.

Room2:

Room reverb with a softer tone than Room1.

Hall1:

Normal hall reverb.

Hall2:

Hall reverb with a softer tone than Hall1.

Plate:

Plate reverb.

Time

Adjust the length (time) of the reverberation.

PreDLY (Pre delay)

Adjust the time until the reverb is output.

Density

Adjust the density of the reverb.

HPF (High pass filter)

Adjust the frequency at which the high pass filter will begin
to take effect. With a setting of Thru, the high pass filter will
not function.

LPF (Low pass filter)

Adjust the frequency at which the low pass filter will begin
to take effect. With a setting of Thru, the low pass filter will
not function.

EFLevel (Effect level)

Adjust the volume of the reverb.

DiLevel (Direct level)

Adjust the volume of the direct sound.

Gate

Turn the gate function on/off. When this is off, the follow-
ing items will not be displayed.

Mode (Gate mode)

Select the way in which the gate function will operate.

Gate:

The gate will begin to open when the direct
signal level exceeds the threshold level, and
will begin to close when it falls below the
threshold level.

Ducking:

The function will be the opposite of the Gate
setting. The gate will begin to close when the
direct signal level exceeds the threshold level,
and will begin to open when it falls below the
threshold level.

Thresh (Threshold)

Adjust the basic level at which opening and closing of the
gate will be controlled.

Reverb

Equalizer

Equalizer

Input L

Input R

Direct Level

Direct Level

Output L

Output R