Varimixer W150 Benutzerhandbuch

                     PLEASE REFER TO THE DIAGRAM ON PAGE 2

1

 

REMOVE NUT (J) AND SHIM WASHERS (H)   

 

 

 

 

 

 

2 

PRY OFF FORK ASSEMBLY (X).   

 

 

 

 

 

 

3 

REMOVE SPECIAL V-BELT (A). 

 

 

 

 

 

 

 

4 

REMOVE TWO 17MM BOLTS (V)   

 

 

 

 

 

 

5 

REMOVE 4 BOLTS FROM MOTORPLATE (T).   

 

 

 

 

 

 

6 

ON OLDER MODEL MIXERS WITH SINGLE PHASE MOTORS,IT MAY BE NECESSARY 

 

 

 

 

 

 

 

 

TO DISCONNECT THE START & RUN CAPACITORS FROM THE SIDE OF THE  

 

 

 

 

 

 

 

 

MOTOR BEFORE LIFTING THE MOTOR OUT OF THE MIXER. 

 

 

 

 

 

 

 

7 

LIFT MOTOR OUT OF MIXER BODY. SET MOTOR ASSEMBLY ON A BOARD LAYED 

 

 

 

  

 

 

ACROSS THE TOP OF THE MIXER.  

 

 

 

 

 

 

8 

DISCONNECT WIRE HARNESS FROM MOTOR. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: DO NOT FOLLOW STEPS 9-12 IF YOU ARE REPLACING THE WHOLE 

 

 

 

 

 

 

 

ASSEMBLY. (MOTOR ,GEARBOX,MOTOR PLATE AND PULLEY. 

 

 

 

 

 

 

9 

GRASP TOP PULLEY (W) AND BANG AGAINST CLAMPING RING & WASHER (S)  

 

 

 

 

 

 

THIS ACTION WILL REMOVE PULLEY FROM MOTOR SHAFT. 

 

 

 

 

 

 

10 

REMOVE 4 SLOTTED HEAD SCREWS FROM MOTOR PLATE TO MOTOR. 

 

 

 

 

 

 

 

REMOVE MOTOR PLATE. 

 

 

 

 

 

 

11 

INSTALL MOTOR PLATE ONTO MOTOR,TIGHTEN 4 SLOTTED HEAD SCREWS.   

 

 

 

 

 

 

INSURE CAPACITORS WILL FACE THE REAR OF THE MIXER WHEN MOTOR IS   

 

 

 

 

 

 

INSTALLED. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 

INSTALL MOTOR PULLEY ONTO MOTOR SHAFT,TAKING CARE TO ALIGN KEY WITH KEYWAY. BANG TOP PULLEY AGAINST BOTTOM

                      PULLEY UNTIL INSTALLED. 

 

 

 

 

 

 

13 

PLACE MOTOR ON TOP OF MIXER AND CONNECT MOTOR TO HARNESS.  (FOLLOW DIAGRAM 

 

ON MOTOR) 

 

 

 

 

 

 

14 

LOWER MOTOR INTO MIXER BODY.INSTALL 4 BOLTS (T) TO THE MOTOR  PLATE. DO NOT TIGHTEN!   

 

 

 

 

15 

INSTALL 2 17MM BOLTS (V) 

 

 

 

 

 

 

16 

MEASURING THE DISTANCE BETWEEN PULLEYS (B),ON 30QT. & 40 QT. THE   

 

 

 

 

 

 

DISTANCE SHOULD BE 11 1/2 INCHES.SLIDE MOTOR TO REACH THIS DISTANCE. 

 

 

 

 

 

 

 

ON 60QT.-150QT.,THE DISTANCE SHOULD BE 12 1/4"S.  

 

 

 

 

 

 

 

 

 

 

 

 

 

17 

TIGHTEN 13 MM BOLTS (T) AND 17 MM BOLTS (V). 

 

 

 

 

NEXT PAGE

Motor Removal Instructions 

Models W30-W150