NuTone NS6500 Series Benutzerhandbuch

WarninG – to reduce the risK oF Fire, electric shocK, 
or inJurY to Persons, oBserve the FolloWinG:
1.  Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.

2.  Before  servicing  or  cleaning  unit,  switch  power  off  at  service

panel  and  lock  service  panel  to  prevent  power  from  being
switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.

3.  Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4.  Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment manufac

-

turer’s guideline and safety standards such as those published
by  the  National  Fire  Protection Association  (NFPA),  and  the
American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.

5.  When  cutting  or  drilling  into  wall  or  ceiling,  do  not  damage

electrical wiring and other hidden utilities.

6.  Ducted fans must always be vented to the outdoors.
7.  Use with approved cord-connection kit only.

8.  To reduce the risk of fire, use only metal ductwork.

to reduce the risK oF a ranGe toP Grease Fire:
1.  Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.

2.  Always turn hood ON when cooking at high heat or when cook

-

ing flaming foods.

3.  Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan or filter.

4.  Use proper pan size. Always use cookware appropriate for the

size of the surface element.

to reduce the risK oF inJurY to Persons in the event 
oF a  ranGe  toP  Grease  Fire,  oBserve  the  FolloW-
inG*:
1.  SMOTHER FLAMES with a close-fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.

2.  NEVER PICK UP A FLAMING PAN - You may be burned.

3.  DO NOT USE WATER, including wet dishcloths or towels - a

violent steam explosion will result.

4.  Use an extinguisher ONLY if:

A.  You know you have a Class ABC extinguisher, and you
already know how to operate it.

 B.  The fire is small and contained in the area where it start-

ed.

 C.  The fire department is being called.

 D.  You can fight the fire with your back to an exit.
* Based on “Kitchen Firesafety Tips” published by NFPA.

1.  For general ventilating use only. do not

use to exhaust hazard-

ous or explosive materials and vapors.

2.  To reduce the risk of fire or electrical shock, this range hood

should not be used with an additional speed control device.

3.  To reduce the risk of shock, disconnect power before servic

-

ing.

4.  To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside.

Recommended mounting height is 18” to 24” from the bottom of the
range hood to the top of the cooking surface.
The  hood  should  be  mounted  to  the  bottom  of  a  standard  wall
cabinet. If the hood must be mounted directly to a wall, secure the
hood to wall studs.
All wiring must comply with local codes and the unit must be properly

grounded. The hood is connected to a 110-120vAC lighting circuit

(15 amp) in the circuit breaker or fuse box.
This range hood is “Convertible” – it may be installed as a ducted

or as a non-ducted unit.

 Purchase  non-ducted  (duct-free)  charcoal  filter  Model

WA65F.

 Ductwork can be installed vertically or horizontally.
 Duct runs should be as short as possible.
 Avoid the use of elbows.
 Use duct tape at all joints.
 Do not use duct smaller than the discharge on the hood.
 For 7” round ductwork installation, use 7” round damper, Model

895 (purchased separately).