Viking VIPR162R Benutzerhandbuch
2
Downdraft Ventilators
VIKING RANGE, LLC
AIR
VENT
VENT
COUNTER
TOP
TOP
BLOWER
BOX
CHIMNEY TOP
COOK TOP
GEAR
MOTOR
COVER
MOTOR
COVER
TYPICAL INSTALLATION
120 VAC
GROUNDED
OUTLET
GROUNDED
OUTLET
This downdraft blower system is
designed to be used to exhaust
airborne contaminants when
cooking with a variety of gas
or electric cooktops. It can be
mounted in island, peninsula,
or conventional wall locations.
This unit can be easily installed
following these basic steps:
designed to be used to exhaust
airborne contaminants when
cooking with a variety of gas
or electric cooktops. It can be
mounted in island, peninsula,
or conventional wall locations.
This unit can be easily installed
following these basic steps:
•
Cut out the countertop
opening.
opening.
• Mount the unit in the
cabinet.
•
Install the Model VIDV500
Interior Blower
Interior Blower
•
Connect the ductwork and
electrical.
electrical.
•
Install the cooktop.
Note: the high level of air fl ow
of this appliance may effect the
gas fl ame on some types of gas
cooktops. This is NORMAL and
will cause no harm, but can
be corrected by lowering the
speed of the blower.
of this appliance may effect the
gas fl ame on some types of gas
cooktops. This is NORMAL and
will cause no harm, but can
be corrected by lowering the
speed of the blower.
PLANNING
Interior Blower Installation
Exterior Blower Installation
Note: the high level of air fl ow of this appliance may effect the
gas fl ame on some types of gas cooktops. This is NORMAL and
will cause no harm, but can be corrected by lowering the speed
of the blower.
gas fl ame on some types of gas cooktops. This is NORMAL and
will cause no harm, but can be corrected by lowering the speed
of the blower.
TYPICAL INSTALLATION
120 VAC
GROUNDED
OUTLET
GROUNDED
OUTLET
AIR
VENT
VENT
GEARMOTOR
COVER
COVER
This downdraft blower system
is designed to be used to ex-
haust airborne contaminants
when cooking with a variety
of gas or electric cooktops.
It can be mounted in island,
peninsula, or conventional
wall locations.
This unit can be easily installed
following these basic steps:
is designed to be used to ex-
haust airborne contaminants
when cooking with a variety
of gas or electric cooktops.
It can be mounted in island,
peninsula, or conventional
wall locations.
This unit can be easily installed
following these basic steps:
•
Cut out the countertop
opening.
opening.
•
Mount the unit in the
cabinet.
cabinet.
•
Install 10" round dis-
charge plate
charge plate
• Install Model VEDV900
or VEDV1200 (48" Model
ONLY) External Blower
ONLY) External Blower
• Connect the ductwork
and electrical.
•
Install the cooktop.
COOK TOP
COUNTER TOP
CHIMNEY TOP
10" ROUND
DISCHARGE
PLATE
DISCHARGE
PLATE
10" ROUND DUCTWORK
ELECTRICAL
SPECIFICATIONS
120 VAC • 60 Hz • 4.0 A
TAKE MEASUREMENTS
All Units
1. Refer to the cooktop installation instructions for dimensions
of cooktop, countertop cut-out, and cabinet requirements.
The Models VIPR102SS and VIPR102RSS will fi t in most 30"
wide cabinets the Models VIPR162SS and VIPR162RSS will
fi t in most 36" wide cabinets and the Models VIPR182SS
and VIPR182RSS will fi t most 48" wide cabinets. However, it
is recommended that oversized cabinets be used for easier
installation.
The Models VIPR102SS and VIPR102RSS will fi t in most 30"
wide cabinets the Models VIPR162SS and VIPR162RSS will
fi t in most 36" wide cabinets and the Models VIPR182SS
and VIPR182RSS will fi t most 48" wide cabinets. However, it
is recommended that oversized cabinets be used for easier
installation.
2. Cooktop depth can vary greatly from one to another. This
may cause the fi t of these two appliances to be rather tight.
Pay special attention to the areas of potential interference
highlighted above. A countertop with (A) a raised lip and/or (B)
a backsplash may not allow enough fl at countertop for a proper
installation. Note that 2" of fl at countertop is required behind
cooktop and that 1-3/4" is necessary between the back edge of
the cooktop and the inside of cabinet back.
highlighted above. A countertop with (A) a raised lip and/or (B)
a backsplash may not allow enough fl at countertop for a proper
installation. Note that 2" of fl at countertop is required behind
cooktop and that 1-3/4" is necessary between the back edge of
the cooktop and the inside of cabinet back.
ELECTRICAL
SPECIFICATIONS
120 VAC • 60 Hz • 6.0 A
(max.)
3-1/4" X 10"
DUCT CONNECTOR
DUCT CONNECTOR