Amana UXT5330AD Merkblatt

Seite von 2
18" (45.7 cm) 
min. clearance 
upper cabinet 
to countertop
36" (91.4 cm) 
base cabinet 
height
13" (33.0 cm)
cabinet depth
30" (76.2 cm) or
36" (91.4 cm) min. 
cabinet opening width
24" (61.0 cm) min. 
30" (76.2 cm) 
suggested max. 
bottom of cabinet 
to cooking surface
Range Hood - 30" (76.2 cm) and 36" (91.4 cm)
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
UXT5330AD
UXT5336AD
Electrical: A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit
is required.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10240582A
10/22/09
LOCATION REQUIREMENTS
29
⁷⁄₈" (75.9 cm) - 30" (76.2 cm) model
35
⁷⁄₈" (91.1 cm) - 36" (91.4 cm) model
1
¹⁄₂"
(3.8 cm)
1"
(2.5 cm)
2"
(5.1 cm)
12"
(30.5 cm)
9"
(22.9 cm)
9"
(22.9 cm)
³⁄₄"
(1.9 cm)
³⁄₈"
(9.5 mm)
7
¹⁄₂"
(19.1 cm)
1
¹⁄₂"
(3.8 cm)
20"
(44.5 cm)
VENTING REQUIREMENTS
Roof Venting
Wall Venting
A. 6" (15.2 cm) or larger round 
vent or a 3
¹⁄₄" x 10" (8.3 x 
25.4 cm) rectangular vent 
through roof
B. Round vent: use 6" (15.2 cm) 
or larger round damper
(purchased separately)
C. Round vent: use 3
¹⁄₄" x 10" 
(8.3 x 25.4 cm) to 6" (15.2 cm) 
or larger diameter transition 
piece (purchased separately)
D. 24" (61.0 cm) - 30" (76.2 cm) 
above cooking surface
E. Roof cap
A. 6" (15.2 cm) or larger round 
vent or a 3
¹⁄₄" x 10" (8.3 x 
25.4 cm) rectangular vent 
through the wall
B. Round vent: use 3
¹⁄₄" x 10" (8.3 
x 25.4 cm) to 6" (15.2 cm) or 
larger diameter transition piece
(purchased separately)
C. 3
¹⁄₄" x 10" (8.3 x 25.4 cm) 
through the wall
D. 24" (61.0 cm) - 30" (76.2 cm) 
above cooking surface
E. Wall cap
A
B
D
C
E
A
B
C
D
E
● 
It is the installer’s responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the left wall.
● 
Range hood location should be away from strong draft areas, such as
windows, doors and strong heating vents.
For Mobile Home Installations
The installation of this range hood must conform to the Manufactured
Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly
the Federal Standard for Mobile Home Construction and Safety, title 24,
HUD, Part 280) or when such standard is not applicable, the standard
for Manufactured Home Installation 1982 (Manufactured Home Sites,
Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition,
or with local codes.
Page 1 of 2
Venting Methods
Vent system can terminate either through the roof or wall. Use 3
¹⁄₄" x 10" 
(8.3 x 25.4 cm) with a maximum vent length of 35 ft (10.7 m) or 6" (15.2 cm)
or larger round vent with a maximum length of 50 ft (15.2 m) for vent system.
NOTE: Flexible vent is not recommended. Flexible vent creates back pressure
and air turbulence that gently reduce performance.