Magnetek Quattro DC Elevator Drive Benutzerhandbuch

 

119 

Brk Pick Flt ....................................................81 

BRK PICK FLT ENA user switch .................. 54 

A 

A to D Fault....................................................80 
A0 - Adjust Menu .....................................30–49 
A1 - Drive Submenu ................................30–38 
A3 - Multistep Ref Submenu ...................41–42 
A5 - Line Side Power Convert Submenu.......46 
A6 - Motor Parameters Submenu............47–49 
AB OFF DELAY parameter ...........................34 
AB ZERO SPD LEV parameter .....................34 
ACCEL JERK IN parameters ........................40 
ACCEL JERK OUT parameters ....................40 
ACCEL RATE parameters.............................40 
ALARM logic output.......................................63 
ALARM+FLT logic output ..............................63 
ANA OUT x GAIN parameter.........................33 
ANA OUT x OFFSET parameter ...................33 
Analog Velocity Follower ...............................23 
ARM CURRENT analog output .....................65 
ARM CURRENT display value ......................68 
ARM INDUCTANCE parameter ....................43 
ARM RESISTANCE parameter .....................43 
ARM VOLTAGE analog output......................65 
ARM VOLTAGE display value.......................68 
ARMATURE IR DROP parameter.................47 
Armature Voltage Feedback..........................24 
ARMATURE VOLTS parameter ....................47 
ARMAUTRE CUR ERR display value ...........68 
ATUO STOP user switch...............................58 
AUTO BRAKE logic output............................63 
AUTO FIELD RES display value ...................68 
AUTO FIELD TC display value......................68 
AUTO FLD INT display value ........................68 
AUTO FLD PROP display value....................68 
AUTO MEAS ARM L display value ...............68 
AUTO MEAS ARM R display value...............68 
Auto Tune Procedure ....................................95 
Automatic Fault Reset ...................................53 
AUX TORQ CMD analog output....................65 
AUX TORQUE CMD display value................66 

B 

Bad Srl Chksm Alarm ....................................80 
BRAKE...........................................................54 
BRAKE HOLD logic output............................63 
BRAKE HOLD TIME parameter ....................31 
BRAKE PICK CNFM user switch ..................54 
BRAKE PICK logic output..............................63 
BRAKE PICK SRC user switch .....................54 
BRAKE PICK TIME parameter......................31 
Bridge Ground Fault ......................................80 
Brk Hold Flt....................................................80 
BRK HOLD FLT ENA user switch .................54 
BRK HOLD FLT logic output .........................63 

BRK PICK FLT logic output .......................... 63 
BUS VOLTAGE analog output...................... 65 
BUS VOLTAGE display value....................... 68 
BUS VREF SOURCE parameter .................. 46 

C 

C2 – Logic Inputs Submenu ................... 61–62 
C3 - Logic Outputs Submenu ................. 63–64 
CAR GOING DWN logic output .................... 63 
CAR GOING UP logic output........................ 63 
Center Frequency - Notch Filter ................... 38 
Changing Carrier Frequency ........................ 44 
CHARGE FAULT logic output....................... 63 
Check Setup Flt ............................................ 81 
Circuit Board Locations - 125A ................... 111 
Circuit Board Locations - 200 / 250 A......... 113 
CLOSE CONTACT logic output.................... 63 
Comm Fault .................................................. 81 
Component Locations - 125A ..................... 109 
Component Locations - 200 / 250 A ........... 110 
Configure C0 Menu................................. 50–65 
Connector Off Flt........................................... 81 
CONT CONFIRM SRC user switch .............. 52 
Cont Pwr Lost Flt .......................................... 82 
CONTACT CFIRM logic input....................... 62 
CONTACT FLT TIME parameter .................. 31 
CONTACTOR D0 DLY parameter ................ 34 
CONTACTOR FLT logic output .................... 63 
CONTRACT CAR SPD parameter ............... 30 
CONTRACT MTR SPD parameter ............... 30 
Control Power Consumption....................... 102 
CTR PWR SENSE logic input....................... 62 
Cube Data Flt................................................ 82 
Cube ID Fault................................................ 82 
Curr Reg Flt .................................................. 82 
CURR REG FLT logic output........................ 63 
CURRENT LIMIT parameter......................... 30 
Customer I/O Board.................................... 115 
Customer Input/Output Connections .......... 115 

D 

D0 - Display D0 Menu............................. 66–69 
D1 - Elevator Data Submenu.................. 66–67 
DC BUS REG I GAIN parameter .................. 46 
DC BUS REG P GAIN parameter................. 46 
DC BUS V BOOST parameter...................... 46 
DC BUS VOLTAGE display value ................ 69 
DC BUS VOLTS REF display value ............. 69 
DCU Data Flt................................................. 82 
DECEL JERK IN parameters........................ 40 
DECEL JERK OUT parameters.................... 40 
DECEL RATE parameters ............................ 40 
Dimensions ............................................. 102–6 
DIR CONFIRM user switch........................... 55