American Standard 1660.100 Series Merkblatt
TM
A M A R I L I S ™
D E L U X E S H O W E R H E A D
B O D Y S I D E S P R AY
B O D Y S I D E S P R AY
30449
A l l p r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
A m e r i c a n S t a n d a r d I n c . 1 9 9 0
C
P r i n t e d i n W e s t G e r m a n y
RECOMMENDED INSTALLATION FOR
MULTIPLE BODY SIDE SPRAYS:
MULTIPLE BODY SIDE SPRAYS:
Installation Instructions for:
ROUGHING-IN DIMENSIONS
P e r s o n a l S h o w e r S y s t e m
1 6 6 0 . 1 0 0 S E R I E S
1 6 6 0 . 1 2 0 S E R I E S
1 6 6 0 . 1 2 0 S E R I E S
1/2"
MAX.
MAX.
6-1/2"
4-3/4"
FINISHED
WALL
WALL
FINISHED
WALL
WALL
OPTIONAL TO
FINISHED FLOOR
USUALLY 65" TO 78".
FOR USE WITH BODY
SIDE SPRAYS 72" TO 78"
IS RECOMMENDED.
SEE
RECOMMENDED
INSTALLATION
BELOW
4"
TO SHOWERHEAD
3 HANDLE
B/S VALVE
16"
16"
TWO-WAY
DIVERTER
VALVE
TUB SPOUT
24"
1/2" S.P.S.
32" OPTIONAL
TO FINISHED
FLOOR
DELUXE SHOWERHEAD
BODY SIDE SPRAY
For maximum flow, use Amarilis 3-Handle
Bath/Shower Valve 8030 or 8031 Series.
Bath/Shower Valve 8030 or 8031 Series.
Connect multiple body side sprays to spout
outlet of valve.
outlet of valve.
Provide two-way diverter valve for addition of
tub spout.
tub spout.
Connect deluxe showerhead to shower outlet
of valve.
of valve.
1
ROUGHING-IN
Prepare shower connection nipples per roughing-in
dimensions. See diagram for recommended 2 and 3
BODY SIDE SPRAY installation.
dimensions. See diagram for recommended 2 and 3
BODY SIDE SPRAY installation.
Cap nipples, turn on water supplies and check for leaks.
2
SHOWERHEAD INSTALLATION
Slide ESCUTCHEON forward and compress
BELLOWS to expose supply connectors.
BELLOWS to expose supply connectors.
Use adjustable wrench to install SHOWERHEAD.
Turn on water supplies and check for leaks.
Push ESCUTCHEON back until seated flush against
wall.
wall.
3
SERVICE
To increase swivel tension:
Compress BELLOWS towards rear to expose ball joint.
Wrench tighten COUPLING NUT to increase tension.
Wrench tighten COUPLING NUT to increase tension.
The FLOW REGULATOR may accumulate debris causing
reduced water flow. To clean, remove SHOWERHEAD,
then:
reduced water flow. To clean, remove SHOWERHEAD,
then:
Remove ESCUTCHEON and BELLOWS.
Unscrew SUPPLY CONNECTOR to remove FLOW
REGULATOR.
Clean FLOW REGULATOR, re-assemble and install
SHOWERHEAD.
Unscrew SUPPLY CONNECTOR to remove FLOW
REGULATOR.
Clean FLOW REGULATOR, re-assemble and install
SHOWERHEAD.
ESCUTCHEON
AND
BELLOWS
SUPPLY
CONNECTOR
FLOW
REGULATOR
COUPLING
NUT
Each installed BODY SIDE SPRAY requires
2.5 GPM for an adequate spray flow.
2.5 GPM for an adequate spray flow.
1/2"
MAX.
MAX.
1-1/2"
1-1/2"
- 2 SPRAY
- 3 SPRAY
28" OPTIONAL
TO FINISHED
FLOOR