Dacor DR30DH-C Benutzerhandbuch

Planning the Installation

Self-Rimming Installation Without 

Raised Vent

•

See page 8 for raised vent installations.

•

Only model DR30DI may be installed in a self-rimming 

configuration. Self-rimming installations create a “built-in” 

look where the trim of the range overlaps the surrounding 

countertop. It is also possible, if the cabinets are the right 

depth, to self rim the front of the range into the cabinet face, 

immediately behind the control panel and door trim. When the 

front of the range is self-rimmed, the 3 1/4” side panels are 

removed.

•

When sliding the range into position, it will stop when the rear 

of the side panels or front panel contacts the notches toward 

the front of the countertop. The rear of the range trim will 

overhang the countertop in back.

Countertop Self-

Rimmed Only

21”  

(53.3 cm)

0” (0 cm) to 

3 1/4” (8.3 cm)

0” (0 cm) to 

5 3/8” (13.7 cm)

Countertop and 

Cabinet Front 

Self-Rimmed

 

1

24 1/4” 

(61.6 cm)

NA

0” (0 cm) to 

2 1/8” (5.4 cm)

1

 Side panels removed 

Countertop height for all self-rimming installations:  

35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum

countertop opening

29 1/4” (74.3 cm)

30” (76.2 cm)

cabinet opening

below countertop

below countertop

To cabinet face

Notch countertop

overhang to width of

cabinets below

1/4” min.* (6 mm)

 countertop

overhang

10” min.

(25.4 cm)

both sides

To countertop

 front

H

J K

Combustible side

wall above range

Rear wall or other 

vertical surface **

** Any vertical surfaces behind the range must be non-combustible 

unless countertop overhang exceeds 2 3/4” (7.0 cm). 

Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm) 

* When increasing overhang, increase dimension H by same amount.

Rear wall or other 

vertical surface **

** Any vertical surfaces behind the range must be non-combustible 

unless countertop overhang exceeds 2 3/4” (7.0 cm). 

Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm) 

* When increasing overhang, increase dimension H by same amount.

countertop and

cabinet opening

Notch countertop to

29 1/4” (74.3 cm)

below countertop

Cabinet face

30” (76.2 cm)

1/4” min.* (6 mm)

 countertop

overhang

10” min.

(25.4 cm)

both sides

To countertop

 front

H

K

Combustible side

wall above range

Cabinet face

Countertop

Back of control

panel and trim

behind door 

rest against

cabinet face

DR30DI[H] range

1/4” min. (6.4 mm)

flat countertop min.

Range side

panels removed

Range trim resting

on countertop

See Top View for required distance

to vertical surfaces

H

Back of cutout

Countertop

DR30DI[H] range

H

1/4” min. (6.4 mm)

flat countertop min.

Range trim resting

on countertop

See Top View for required distance

to vertical surfaces

Cabinet face

Back of

cutout

Back of

control

panel

3 1/4 inch

side panel