Meco 2400 Benutzerhandbuch
STEP 5) Portable Use of Lantern:
Lantern can be connected to a 1 lb.
cylinder for use as a portable light.
(FIG. 7G) Hold the Lantern with
one hand. Insert the LP cylinder
into the Lantern nozzle with other
hand. Turn LP cylinder until snug.
Follow leak test procedure on page
12 before using.
cylinder for use as a portable light.
(FIG. 7G) Hold the Lantern with
one hand. Insert the LP cylinder
into the Lantern nozzle with other
hand. Turn LP cylinder until snug.
Follow leak test procedure on page
12 before using.
FIG. 7G
INSTALL GREASE CONTAINER
To reduce the risk of serious bodily injury or death:
· Never light the LP gas grill without the Grease
· Never light the LP gas grill without the Grease
Container in place.
FIG. 8A
From underneath the grill, align the tab and Grease
Container opening with that in the bottom of the
Bowl. (FIG. 8A) Push the Grease Container in and
rotate the V-shape end until it locks into position
under the bracket in the Bowl bottom. (Fig. 8B)
Container opening with that in the bottom of the
Bowl. (FIG. 8A) Push the Grease Container in and
rotate the V-shape end until it locks into position
under the bracket in the Bowl bottom. (Fig. 8B)
FIG. 8B
STEP 4) Assemble Lantern & Tube to Grill:
Remove the gas tube clip from under the leg by
loosening the two screws securing it. (This is for
store display grills and not needed for your use.)
Just re-tighten the screws into the leg. (FIG. 7C)
Remove the gas tube clip from under the leg by
loosening the two screws securing it. (This is for
store display grills and not needed for your use.)
Just re-tighten the screws into the leg. (FIG. 7C)
FIG. 7D
Remove Lantern Gas Tube
Clip attached to inside leg.
FIG. 7C
FIG. 7A
FIG. 7B
Insert Gas
Tube into
PTO
TM
Insert the crooked end of the Lantern gas tube into
the rear leg PTO
the rear leg PTO
TM
opening. (FIG. 7D) Note: In
order for the Lantern gas tube to be upright, it
must be secured to the LP cylinder and the
cylinder must be secured in the leg holder. You
may delay gas tube installation until instructed
on pages 10 & 11 or proceed there now to
secure the gas tube.
must be secured to the LP cylinder and the
cylinder must be secured in the leg holder. You
may delay gas tube installation until instructed
on pages 10 & 11 or proceed there now to
secure the gas tube.
Rotate the Lantern head around the gas tube to the
desired position for access and use. Make sure
gas tube is turned properly to allow hood to open.
desired position for access and use. Make sure
gas tube is turned properly to allow hood to open.
STEP 3) Assemble Lantern and Gas Tube: Insert
the gas tube into the lantern nozzle. (FIG. 7A)
Engage the knurled coupling into the lantern and
turn until snug. (FIG. 7B) Be careful not to cross
thread the connection.
the gas tube into the lantern nozzle. (FIG. 7A)
Engage the knurled coupling into the lantern and
turn until snug. (FIG. 7B) Be careful not to cross
thread the connection.
To reduce the risk of serious bodily injury or death:
· Always burn portable lantern on a flat level surface in
· Always burn portable lantern on a flat level surface in
an upright position away from any flammable
substances.
substances.
· When carrying Portable Lantern, hold it away from you
and do not run with it.
· Do not use gas tube with Lantern and 1 pound LP
cylinder when using Lantern as a portable light. It is not
stable and will cause lantern to fall over.
stable and will cause lantern to fall over.
· To prevent being knocked over, always disconnect
lantern and LP cylinder before storing.
· Do not allow children to use the portable lantern. Keep
bystanders, children and pets away from the lantern.
9