Desa CDCFTN Benutzerhandbuch
111244-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
19
19
INSTALLING LOG SET AND SCREEN
1.
Remove log packaging material and discard packaging. Gen-
tly place log over burner (see Figure 34). Do not allow log to
contact flame. If flame contacts log, soot will be created.
tly place log over burner (see Figure 34). Do not allow log to
contact flame. If flame contacts log, soot will be created.
2.
Reattach screen by placing the notches in the screen frame
over the shoulder screws and pushing down.
over the shoulder screws and pushing down.
Log
Shoulder Screw
Screen
INSTALLATION
Continued
INSTALLATION
Installing Log Set and Screen
OPERATING FIREPLACE (THERMOSTAT-CONTROLLED MODELS)
For Your Safety Read Before Lighting
Lighting Instructions
Figure 34 - Installing Log and Screen
OPERATING FIREPLACE
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
FOR YOUR SAFETY
READ BEFORE LIGHTING
THERMOSTAT-CONTROLLED MODELS
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire de-
partment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don’t try to repair it, call a qualified service techni-
cian or gas supplier. Force or attempted repair may result
in a fire or explosion.
hand, don’t try to repair it, call a qualified service techni-
cian or gas supplier. Force or attempted repair may result
in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
WARNING: You must operate this fireplace with
the screen in place. Make sure fireplace screen is
installed before running fireplace.
installed before running fireplace.
NOTICE: During initial operation of new fireplace,
burning logs will give off a paper-burning smell. Open
window to vent smell. Operate fireplace on HI position
to burn off odor. This will only last a few hours.
burning logs will give off a paper-burning smell. Open
window to vent smell. Operate fireplace on HI position
to burn off odor. This will only last a few hours.
1.
STOP! Read the safety information above.
2.
Make sure equipment shutoff valve is fully open.
3.
Turn control knob clockwise
Clockwise
to the OFF position.
4.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information in column 1. If you don’t
smell gas, go to the next step.
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information in column 1. If you don’t
smell gas, go to the next step.
5.
Turn control knob counterclockwise
C-clockwise
to the PI-
LOT position. Press in control knob for five (5) seconds
(see Figure 35).
(see Figure 35).
Note:
You may be running this fireplace for the first time
after hooking up to gas supply. If so, the control knob may
need to be pressed in for 30 seconds or more. This will al-
low air to bleed from the gas system.
• If control knob does not pop out when released, contact
need to be pressed in for 30 seconds or more. This will al-
low air to bleed from the gas system.
• If control knob does not pop out when released, contact
a qualified service person or gas supplier for repairs.
Figure 35 - Control Knob In The OFF Position
Ignitor
Button
Button
Control Knob