Grizzly T24631 Benutzerhandbuch
The Model T24631 spiral cutterhead is designed
to replace the straight-knife cutterhead on the
Model G0656/G0656P 8" Jointer.
to replace the straight-knife cutterhead on the
Model G0656/G0656P 8" Jointer.
CoPyriGhT © JULy, 2012 By GrizzLy indUsTriaL, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#Tr15167 PrinTed in China
items needed for installation
Wrench 14mm ................................................... 1
Wrench 17mm.................................................... 1
socket driver 1/4" .............................................. 1
Precision straightedge ..................................... 1
Feeler Gauge set (sizes not important) ............ 1
Pulley Puller ....................................................... 1
Pair of heavy Leather Gloves ........................... 1
rubber dead Blow hammer ............................. 1
2x4 Wood Block 4" Long ................................... 1
Wrench 17mm.................................................... 1
socket driver 1/4" .............................................. 1
Precision straightedge ..................................... 1
Feeler Gauge set (sizes not important) ............ 1
Pulley Puller ....................................................... 1
Pair of heavy Leather Gloves ........................... 1
rubber dead Blow hammer ............................. 1
2x4 Wood Block 4" Long ................................... 1
inventory
(
figure 2)
a. spiral Cutterhead w/inserts ........................ 1
b. Torx drivers T20 ........................................ 2
c. Torx L-Wrenches T20 ................................ 2
d. Flat head Torx screws T20 M6-1 x 15 ...... 3
e. indexable Carbide inserts 14 x 14 x 2 ....... 5
figure 2.
spiral cutterhead inventory.
C
d
B
a
e
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
model t24631
8" spiral cutterhead
installation instructions
introduction
figure 1. T24631 spiral Cutterhead.
it takes approximately one hour to install this
cutterhead and re-adjust the jointer. The job con-
sists of (1) removing the old cutterhead, (2) install-
ing/shimming the new spiral cutterhead, and (3)
re-adjusting the outfeed table to be even with the
carbide inserts at TdC (top dead center).
cutterhead and re-adjust the jointer. The job con-
sists of (1) removing the old cutterhead, (2) install-
ing/shimming the new spiral cutterhead, and (3)
re-adjusting the outfeed table to be even with the
carbide inserts at TdC (top dead center).
note: We strongly recommend replacing the
old cutterhead bearings during installation.
recommended, but not required
inch/Pound Torque Wrench. .............................. 1
arbor Press ....................................................... 1
Ball Bearing 6204zz .......................................... 1
Ball Bearing 6203zz ......................................... 1
arbor Press ....................................................... 1
Ball Bearing 6204zz .......................................... 1
Ball Bearing 6203zz ......................................... 1
specifications
Length ...............................................................8"
diameter ...........................................................3"
number of spirals .............................................. 4
number of inserts ............................................ 40
insert size ....................................14 x 14 x 2mm
insert screw Thread size ......................... M6-1.0
shaft diameter (Long side) ....................... 20mm
shaft diameter (short side) .......................17mm
Weight .......................................................18 lbs.
diameter ...........................................................3"
number of spirals .............................................. 4
number of inserts ............................................ 40
insert size ....................................14 x 14 x 2mm
insert screw Thread size ......................... M6-1.0
shaft diameter (Long side) ....................... 20mm
shaft diameter (short side) .......................17mm
Weight .......................................................18 lbs.