Electrolux TINSEB504MRR0 Benutzerhandbuch
E2
MICROWAVE WALL OVEN INSTALLATION INSTRUCTIONS
IMPORTANT NOTES TO
THE INSTALLER
Read all instructions contained in these installation
1.
instructions before installing the Microwave Wall Oven.
This oven can be built into a cabinet or wall by itself or
above any electric wall oven or warming drawer.
This oven can be built into a cabinet or wall by itself or
above any electric wall oven or warming drawer.
Remove all packing material from inside the oven cavity
2.
before connecting the electrical supply to the Microwave
Wall Oven. DO NOT REMOVE THE WAVEGUIDE COVER,
which is located on the cavity ceiling. See Figure 2A.
Wall Oven. DO NOT REMOVE THE WAVEGUIDE COVER,
which is located on the cavity ceiling. See Figure 2A.
Remove the 2 shipping duct supports (see Figure 2B) by
3.
removing the 2 screws securing each side. Reinsert 2
screws (each side) to secure the stainless cover.
screws (each side) to secure the stainless cover.
Remove the feature sticker, if there is one, from the
4.
outside of the door.
Check the oven for any damage, such as misaligned or
5.
bent door, damaged door seals and sealling surfaces,
broken or loose door hinges and latches and dent
inside the cavity or on the door.
broken or loose door hinges and latches and dent
inside the cavity or on the door.
Observe all governing codes and local ordinances.
6.
Be sure to leave these instructions with the consumer.
7.
IMPORTANT NOTE TO
THE CONSUMER
Keep these instructions with your Owner's Guide for future
reference.
reference.
IMPORTANT SAFETY
INSTRUCTIONS
Never use your appliance for warming or heating
the room. Prolonged use of the oven without adequate
ventilation can be dangerous.
the room. Prolonged use of the oven without adequate
ventilation can be dangerous.
Carpentry
Refer to Figure 1 for the dimensions required for your
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar
material, the surface must be level from side to side and
from front to rear.
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar
material, the surface must be level from side to side and
from front to rear.
Electrical Requirements
The appliance operates on a 120 volt, 60 Hz electrical
supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.
supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.
Observe all governing codes and local ordinances
To prevent damage to the oven control, during cold
temperature weather, wait at least three (3) hours
after receiving this oven before supplying power to
the appliance. This will prevent possible damage to the
built-in oven control at power on.
temperature weather, wait at least three (3) hours
after receiving this oven before supplying power to
the appliance. This will prevent possible damage to the
built-in oven control at power on.
Cabinet Installation
The Microwave Wall Oven can tip when the door
is open. The Anti-Tip brackets supplied with the
Microwave Wall Oven must be attached to the
cabinet and the appliance to prevent tipping of
the unit and injury to persons.
is open. The Anti-Tip brackets supplied with the
Microwave Wall Oven must be attached to the
cabinet and the appliance to prevent tipping of
the unit and injury to persons.
ANTI-TIP BRACkETS INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Unpack the Microwave Wall Oven and find the 2
1.
Anti-Tip brackets and screws included in the literature
package.
package.
Install the Anti-Tip bracket in the cabinet as shown
2.
on Figure 3.
Note: To prevent damage to cabinet, it
is recommended to drill ¹/
16
" (0.16 cm) diameter pilot
holes before installing the Anti-Tip brackets.
If there is any damage,
DO NOT operate the
oven and contact your dealer or ELECTROLUX
AUTHORIZED SERVICER.
AUTHORIZED SERVICER.
Figure 2A
Figure 2B
Safety
Door Latch
Hinge
Oven Cavity
Waveguide Cover
Door Seals
and Sealing
Surfaces