Desa (V)V42ENA(1) Series Benutzerhandbuch
111907-01C
For more information, visit www.desatech.com
For more information, visit www.desatech.com
16
01800
Horizontal Square High Wind Termination (1)
01801
14" Snorkel Termination - Galvanized (1)
01802
36" Snorkel Termination - Galvanized (1)
DESA Venting Accessories
Number Description
01504
Firestop Plate (4)
01505
Adjustable Roof Flashing 0 to 8/12 - Galvanized (6)
01506
Steep Pitch Flashing 9/12 to 12/12 - Galvanized (6)
01507
Storm Collar - Galvanized (4)
01508
Wall Strap (4)
01514
Combustible Siding Standoff - Galvanized (1)
01607
Wall Firestop - Galvanized (4)
VR-58
Vertical Restrictor - Galvanized
VENTING INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Continued
PARTS LISTS FOR VENTING KITS AND
COMPONENTS FOR VV421 SERIES
COMPONENTS FOR VV421 SERIES
DESA (5/8") Pipe & Vent Kits
Number Description
01492
Horizontal Square Termination Kit
Includes: 45° Elbow (Through 5" Wall), Wall Firestop,
Horizontal Square Termination
Horizontal Square Termination
01493
Basic Vertical Termination Kit
Includes: Vertical Termination, Adjustable Flashing,
Storm Collar
Storm Collar
01491
Horizontal Round Termination Kit
Includes: Round Termination, Wall Firestop, and
45° Elbow (Through 5" Wall)
45° Elbow (Through 5" Wall)
01497
12" Section Coaxial Pipe - Galvanized (4)
01498
18" Section Coaxial Pipe - Galvanized (4)
01499
24" Section Coaxial Pipe - Galvanized (4)
01500
36" Section Coaxial Pipe - Galvanized (4)
01501
48" Section Coaxial Pipe - Galvanized (4)
01513
6" Section Coaxial Pipe - Galvanized (4)
01606
Adjustable 17"-24" Section Coaxial Pipe -
Galvanized (4)
F8030
Adjustable 7"-12" Section Coaxial Pipe - Galvanized (6)
D1032
Adjustable 7"-12" Section Coaxial Pipe - Galvanized (1)
DESA Elbows
Number Description
01502
45° Elbow - Galvanized (4)
01503
90° Elbow - Galvanized (4)
DESA Terminations
Number Description
01494
Vertical Round Termination - Galvanized (1)
01495
Horizontal Round Termination - Galvanized (1)
01496
Horizontal Square Termination - Galvanized (1)
01798
Vertical Round High Wind Termination (1)
FIREPLACE INSTALLATION
VENTING INSTALLATION INSTRUCTIONS
Parts Lists for Venting Kits and Components for V42 and VV42 Series (Cont.)
Parts Lists for Venting Kits and Components for VV421 Series
Parts Lists for Venting Kits and Components for VV421 Series
FIREPLACE INSTALLATION
Check Gas Type
Installing Optional Blower Accessory
Installing Optional Blower Accessory
Model BK Installation
Follow all instructions provided in the blower accessory kit.
1.
Attach the power cord to the blower motor by firmly pushing the
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25, page 17).
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25, page 17).
2.
Attach green ground wire from power cord to blower hous-
ing using screw provided (see Figure 25, page 17). Tighten
screws securely.
ing using screw provided (see Figure 25, page 17). Tighten
screws securely.
3.
Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward. The blower
will fit inside the back opening and be held in position against
the back wall by the magnets (see Figure 25, page 17).
wrapper with the exhaust port directed upward. The blower
will fit inside the back opening and be held in position against
the back wall by the magnets (see Figure 25, page 17).
INSTALLING OPTIONAL BLOWER
ACCESSORY
ACCESSORY
NOTICE: If installing blower in an existing fireplace
with gas connections, shut off gas supply and dis-
connect heater from gas supply. Contact a qualified
service person to do this.
with gas connections, shut off gas supply and dis-
connect heater from gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex electrical outlet
installed in the right side of the bottom of the fireplace
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
CHECK GAS TYPE
Use proper gas type for the fireplace unit you are installing. If your
gas supply is not correct, do not install fireplace. See retailer where
you purchased the fireplace for proper fireplace according to your
gas type or to purchase gas conversion kit (see Accessories, page 37).
gas supply is not correct, do not install fireplace. See retailer where
you purchased the fireplace for proper fireplace according to your
gas type or to purchase gas conversion kit (see Accessories, page 37).
PARTS LISTS FOR VENTING KITS AND COMPO-
NENTS FOR V42 AND VV42 SERIES (CONT.)
NENTS FOR V42 AND VV42 SERIES (CONT.)
Number Description
VR-58
Vertical Restrictor, Galvanized
S-58
Vinyl Siding Standoff, Galvanized
WS-58
Wall Strap
CS-58
Cathedral Ceiling Support
FP-58
Firestop Plate
SF-58
Stucco Flashing - For use with HTS-5