Mitsubishi wd-52628 Benutzerhandbuch
30
Chapter 2. Connecting
Connecting an HDTV Cable Box or Satellite Receiver with
Component Video
Connecting an HDMI Device
Component Video
Connecting an HDMI Device
HDTV Cable Box or Satellite Receiver
with Component Video
with Component Video
Figure 11
A coaxial splitter, RCA component video cables, and audio
cables are required. These are not included with the TV.
A coaxial splitter, RCA component video cables, and audio
cables are required. These are not included with the TV.
1. Connect the outside antenna, cable, or satellite to
ANT or SATELLITE IN on the cable box or satellite
receiver. See your device’s owner’s guide for
instructions and cable compatibility.
receiver. See your device’s owner’s guide for
instructions and cable compatibility.
2. Connect the incoming terrestrial antenna or cable (not
satellite) to ANT-1 on the TV back panel (a coaxial
splitter, available at most electronic supply stores,
may be required to complete this installation).
splitter, available at most electronic supply stores,
may be required to complete this installation).
COMPONENT
YPbPr (480i/480p/720p/1080i)
INPUT
1
2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN
ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT
CableCARD™
USE WITH
ANT 1 CARD TOP
1
2
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
1
2
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
2
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¸
'
,INK
¸
INPUT
PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720
7*%&0
:
1S
1C
47*%&0
7$3
$0/530-
1)0/&+"$,
3'
3&.05&
0655057
$)
$)
$)
$"65*0/
3*4,0'&-&$53*$"-4)0$,
%0/0501&/
%*(*5"-
"6%*0065
4"5&--*5&*/
*/'30."/5
"6%*0
-
3
"6%*0
-
3
7*%&0
57#BDL1BOFM4FDUJPO
3FE
8IJUF
*ODPNJOH
"OUFOOBPS
$BCMF
"OUFOOBPS
$BCMF
)%573FDFJWFSXJUI
:1S1CDPOOFDUJPOT
:1S1CDPOOFDUJPOT
5PBOUFOOB
DBCMF PSTBUFMMJUF
DBCMF PSTBUFMMJUF
PS
3FE
8IJUF
Figure 11. Connecting an External HDTV Receiver with
Component Video Connections
3. Connect RCA-type cables from the YPrPb outputs on
Component Video Connections
3. Connect RCA-type cables from the YPrPb outputs on
the HDTV receiver to Component-1 on the TV back
panel, matching the correct connections:
panel, matching the correct connections:
HDTV Receiver to TV Back panel
•
Y to Y
•
Pr to Pr
•
Pb to Pb
4. Connect L (left) and R (right) audio cables from the
DTV receiver to Component-1 AUDIO on the TV back
panel.
panel.
5. If you are using a satellite receiver, you must
change the input through NetCommand. Open the
NetCommand Connection for [Device] screen (see
page 50) to make the change.
NetCommand Connection for [Device] screen (see
page 50) to make the change.
Note: To receive the benefits of a digital A/V receiver,
connect your cable box or satellite receiver’s digital audio
out to a digital input on your digital A/V receiver.
connect your cable box or satellite receiver’s digital audio
out to a digital input on your digital A/V receiver.
HDMI Device
Figure 12
An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required. You can connect two HDMI devices to the TV
back panel through the HDMI connections.
back panel through the HDMI connections.
CableCARD™
USE WITH
ANT 1 CARD TOP
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
2
IEEE 1394
INPUT/
OUTPUT
PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720
DIGITAL
AUDIO
OUTPUT
)%.*%FWJDF
57
Figure 12. Connecting an HDMI Device
Note: To use the benefits of digital surround sound from
the HDMI device, connect the digital audio output of the
HDMI device directly to the A/V receiver.
the HDMI device, connect the digital audio output of the
HDMI device directly to the A/V receiver.