Sony dvp-ns92v Betriebsanweisung
84
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 21).
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
, Super Audio CD audio signals are not
output from the DIGITAL OUT (OPTICAL
or COAXIAL)/HDMI OUT jack.
or COAXIAL)/HDMI OUT jack.
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
, When playing multichannel MPEG audio
soundtracks, only the Front (L) and Front
(R) signal will be output from your two
front speakers.
(R) signal will be output from your two
front speakers.
, The equipment connected to the HDMI
OUT jack does not conform to the audio
signal format, in this case set
“AUDIO(HDMI)” in “AUDIO SETUP” to
“PCM” (page 77).
signal format, in this case set
“AUDIO(HDMI)” in “AUDIO SETUP” to
“PCM” (page 77).
No sound is output from the HDMI OUT
jack
jack
, Try the following: 1Turn the player off
and on again. 2Turn the connected
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
, The HDMI OUT jack is connected to a DVI
device (DVI jacks do not accept audio
signals).
signals).
, The HDMI OUT jack does not output Super
Audio CD sound.
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
The sound volume is low.
, The sound volume is low on some DVDs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“OFF” (page 77).
The surround effect is difficult to hear
when you are playing a Dolby Digital,
MPEG audio, or DTS sound track.
when you are playing a Dolby Digital,
MPEG audio, or DTS sound track.
, Check the speaker connections and setting
, The 5.1 channel sound is not recorded on
the disc being played.
The sound comes from the centre speaker
only.
only.
, Depending on the disc, the sound may come
from the centre speaker only.
, Set the surround mode setting to “OFF”
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
down.
, The disc is skewed.
, The player cannot play certain discs
, The player cannot play certain discs
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 3).
, The player cannot play a recorded disc that
is not correctly finalized (page 7).
The MP3 audio track cannot be played
(page 59).
(page 59).
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conform to UDF (Universal
Disk Format).
Disk Format).
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even