Enterasys csx150 Betriebsanweisung
USER’S GUIDE
150 CyberSWITCH
B
RIDGE
I
NFORMATION
C
ONFIGURATION
E
LEMENTS
IP (S
UB
) N
ETWORK
N
UMBER
If the CyberSWITCH uses an IP RLAN interface to connect to a remote bridge, you must provide
this information.
this information.
This address associates the bridge with the IP network to which it connects. Enter this address
using dotted decimal notation. This parameter applies to the network-portion of the IP address
only. Note that if you change the IP address under the IP information menu selection, this parameter
will reflect that change.
using dotted decimal notation. This parameter applies to the network-portion of the IP address
only. Note that if you change the IP address under the IP information menu selection, this parameter
will reflect that change.
E
NABLE
/D
ISABLE
B
RIDGING
You may enable or disable bridging on a per device basis. You must enable bridging for remote
LAN devices, which indicates that the remote device is a bridge and not a router.
LAN devices, which indicates that the remote device is a bridge and not a router.
M
AKE
C
ALLS
FOR
B
RIDGE
DATA
You must enable this element to allow bridge dial out to function. You must also complete the
following configuration:
•
following configuration:
•
Enable bridging at the system level and at the per-device level.
•
Either add the device to the CyberSWITCH’s Known Connect List, or configure a bridge con-
nection filter. For information regarding the Known Connect List,
nection filter. For information regarding the Known Connect List,
. For infor-
.
Note: This feature is not yet supported for IPX Remote LANs.
IPX R
EMOTE
LAN N
ETWORK
N
UMBER
If the CyberSWITCH uses an IPX RLAN interface to connect to a remote bridge, you may choose to
change this information.
change this information.
This parameter associates the bridge with the IPX network to which it connects. Enter the IPX
external network number of the remote LAN, or accept the default value of none.
external network number of the remote LAN, or accept the default value of none.
If this parameter remains none, the CyberSWITCH will assume the network number is that of the
first configured IPX Remote LAN interface. This is convenient in applications in which remote
LANs consist only of clients (thus no explicit external network address), all of which are on the
same external virtual LAN.
first configured IPX Remote LAN interface. This is convenient in applications in which remote
LANs consist only of clients (thus no explicit external network address), all of which are on the
same external virtual LAN.
If you choose to change this parameter, you must specify the IPX external network number used
on the remote LAN in question. This value must be the same as the value configured for the
corresponding IPX Remote LAN interface.
on the remote LAN in question. This value must be the same as the value configured for the
corresponding IPX Remote LAN interface.
IPX S
POOFING
O
PTIONS
Note: This feature is not yet supported for IPX Remote LANs. Do not attempt to configure.
A
PPLE
T
ALK
N
ETWORK
N
UMBER
If the CyberSWITCH uses an AppleTalk WAN (Remote LAN) port to connect to a remote bridge,
you may choose to change this information.
you may choose to change this information.
This parameter associates the bridge with the AppleTalk network to which it connects. Enter the
AppleTalk network number/range (which corresponds to a configured AppleTalk Remote LAN
port), or accept the default value of none. If this parameter remains none, the CyberSWITCH will
assume an association with the first configured AppleTalk Remote LAN port.
AppleTalk network number/range (which corresponds to a configured AppleTalk Remote LAN
port), or accept the default value of none. If this parameter remains none, the CyberSWITCH will
assume an association with the first configured AppleTalk Remote LAN port.