Enterasys 6e128-26 Betriebsanweisung
Chapter 2: Network Requirements
2-2
6E128-26, 6E138-25, 6E129-26 and 6E139-25 User’s Guide
2.2
10BASE-F NETWORK
When connecting a 10BASE-F segment to any of the 6E128-26 and
6E138-25 ports (Interfaces 1 through 24), ensure that the network meets
the Ethernet network requirements of the IEEE 802.3 standard for
10BASE-F. Refer to the Cabletron Systems Cabling Guide for details.
6E138-25 ports (Interfaces 1 through 24), ensure that the network meets
the Ethernet network requirements of the IEEE 802.3 standard for
10BASE-F. Refer to the Cabletron Systems Cabling Guide for details.
2.3
FOIRL NETWORK
When connecting a FOIRL single mode segment to any of the 6E129-26
and 6E139-25 ports (Interfaces 1 through 24), ensure that the network
meets the Ethernet network requirements of the IEEE 802.3 standard for
FOIRL. Refer to the Cabletron Systems Cabling Guide for details.
and 6E139-25 ports (Interfaces 1 through 24), ensure that the network
meets the Ethernet network requirements of the IEEE 802.3 standard for
FOIRL. Refer to the Cabletron Systems Cabling Guide for details.
2.4
100BASE-TX NETWORK
The 6E12X-26, with an FE-100TX installed in ports 25 and 26, provides
an RJ45 connection that supports Category 5 UTP cabling. The device at
the other end of the twisted pair segment must meet IEEE 802.3u
100BASE-TX Fast Ethernet network requirements for the devices to
operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for
details.
an RJ45 connection that supports Category 5 UTP cabling. The device at
the other end of the twisted pair segment must meet IEEE 802.3u
100BASE-TX Fast Ethernet network requirements for the devices to
operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for
details.
2.5
100BASE-FX FIBER OPTIC NETWORK
Ports 25 and 26 of the 6E12X-26 support the Cabletron Systems
FE-100FX and FE-100F3 fiber optic interface modules. The device at the
other end of the fiber optic segment must meet the 100BASE-FX Fast
Ethernet network requirements to operate at 100 Mbps. Refer to the
Cabletron Systems Cabling Guide for details.
FE-100FX and FE-100F3 fiber optic interface modules. The device at the
other end of the fiber optic segment must meet the 100BASE-FX Fast
Ethernet network requirements to operate at 100 Mbps. Refer to the
Cabletron Systems Cabling Guide for details.
Multimode Mode Fiber Optic Cable Length
The maximum multimode fiber optic cable length of a 100BASE-FX
segment is covered in the Cabletron Systems Cabling Guide.
segment is covered in the Cabletron Systems Cabling Guide.
Single Mode Fiber Cable Lengths
The maximum single mode fiber optic length of a 100BASE-FX segment
may be no more than 5 km between Data Terminal Equipment (DTE to
DTE) in half duplex mode or 20 km (DTE to DTE) in full duplex mode.
may be no more than 5 km between Data Terminal Equipment (DTE to
DTE) in half duplex mode or 20 km (DTE to DTE) in full duplex mode.
NOTE
The 6E12X-26 with an FE-100TX installed is capable of
operating at either 10 or 100 Mbps. The FE-100TX can
automatically sense the speed of the other device and adjust
its speed accordingly.
operating at either 10 or 100 Mbps. The FE-100TX can
automatically sense the speed of the other device and adjust
its speed accordingly.