Kenwood ddx7034bt Installationsanweisungen
2
|
DNX7140/DNX7000EX/DDX714/DDX7034BT
Installation Procedure
1
..........1
2
..........1
3
..........1
4
..........1
5
..........2
6
..........1
7
..........1
8
..........6
9
..........6
0
..........1
!
DNX models only
..........1
@
DNX models only
..........1
#
..........1
$
DNX models only
..........1
Accessories
1. To prevent a short circuit, remove the key from the
ignition and disconnect the
- battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the
6. Install the unit in your car.
7. Reconnect the
- battery.
8. Press the reset button.
9. Perform the Initial Setup. (Refer to the Instruction
9. Perform the Initial Setup. (Refer to the Instruction
Manual.)
2WARNING
• If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.
to the wires via the fuse.
Acquiring GPS Signals
The first time you turn on the DNX models, you must
wait while the system acquires satellite signals for
the first time. This process could take up to several
minutes. Make sure your vehicle is outdoors in an
open area away from tall buildings and trees for
fastest acquisition. After the system acquires satellites
for the first time, it will acquire satellites quickly each
time thereafter.
wait while the system acquires satellite signals for
the first time. This process could take up to several
minutes. Make sure your vehicle is outdoors in an
open area away from tall buildings and trees for
fastest acquisition. After the system acquires satellites
for the first time, it will acquire satellites quickly each
time thereafter.
About the Front Panel
When removing the product from the box or installing
it, the front panel may be positioned at the angle
shown in (Fig. 1). This is due to the characteristics of a
mechanism the product is equipped with.
If the program that is activated when the product is
first powered on works properly, the front panel will
automatically move into the position (initial setting
angle) shown in (Fig. 2).
it, the front panel may be positioned at the angle
shown in (Fig. 1). This is due to the characteristics of a
mechanism the product is equipped with.
If the program that is activated when the product is
first powered on works properly, the front panel will
automatically move into the position (initial setting
angle) shown in (Fig. 2).
(Fig. 1)
(Fig. 2)
⁄
• About the model groups
If different functions are
If different functions are
used in different model
groups, the model groups
are described as shown
below.
groups, the model groups
are described as shown
below.
Names of models included
in each model group are as
follows:
DNX models
DNX7140, DNX7000EX
DDX models
DDX714, DDX7034BT
follows:
DNX models
DNX7140, DNX7000EX
DDX models
DDX714, DDX7034BT
B54-4714-10_01_K_EFS.indb 2
B54-4714-10_01_K_EFS.indb 2
09.2.16 5:00:10 PM
09.2.16 5:00:10 PM