Jet 690082 jtm-1 - 9" x 42" 2 hp 3-phase vertical milling machine Betriebsanweisung
4
3.0 Safety warnings
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
comply with all of these warnings may cause
serious injury.
3. Replace the warning labels if they become
obscured or removed.
4. This turret mill is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a turret mill, do
not use until proper training and knowledge
have been obtained.
personnel only. If you are not familiar with the
proper and safe operation of a turret mill, do
not use until proper training and knowledge
have been obtained.
5. Do not use this turret mill for other than its
intended use. If used for other purposes,
Walter Meier (Manufacturing) Inc., disclaims
any real or implied warranty and holds itself
harmless from any injury that may result from
that use.
Walter Meier (Manufacturing) Inc., disclaims
any real or implied warranty and holds itself
harmless from any injury that may result from
that use.
6. Always wear approved safety glasses/face
shields while using this mill. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
eyeglasses only have impact resistant lenses;
they are not safety glasses.
7. Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Remove all loose
clothing and confine long hair.
sleeves up past the elbows. Remove all loose
clothing and confine long hair.
8. Non-slip safety footwear and anti-skid floor
strips are recommended. Do not wear gloves.
9. Never place hands near or around a revolving
tool or part.
10. Wear ear protectors (plugs or muffs) during
extended periods of operation.
11. Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contain chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
activities contain chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
Lead from lead based paint.
•
Crystalline silica from bricks, cement and
other masonry products.
other masonry products.
•
Arsenic and chromium from chemically
treated lumber.
treated lumber.
Your risk of exposure varies, depending on
how often you do this type of work. To reduce
your exposure to these chemicals, work in a
well-ventilated area and work with approved
how often you do this type of work. To reduce
your exposure to these chemicals, work in a
well-ventilated area and work with approved
safety equipment, such as face or dust masks
that are specifically designed to filter out
microscopic particles.
that are specifically designed to filter out
microscopic particles.
12. Do not operate this machine while tired or
under the influence of drugs, alcohol or any
medication.
medication.
13. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
supply.
14.
Make certain the machine is properly
grounded.
grounded.
15. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
source.
16. Workpiece must be attached or clamped to the
table. Never hold a workpiece with your hand.
17. Use correct spindle speed and table feed for
the particular job.
18. Do not start machine with cutter in contact with
workpiece.
19. Disengage power feed when not in use.
20. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and
adjusting wrenches are removed from the
machine before turning it on.
adjusting wrenches are removed from the
machine before turning it on.
21. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
22. Check damaged parts. Before further use of
the machine, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
23. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
24. Keep the floor around the machine clean and
free of scrap material, oil and grease.
25. Keep visitors a safe distance from the work
area. Keep children away.
26. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
27. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in
serious injury.
play” are careless acts that can result in
serious injury.