Phase Technology cs-525 Betriebsanweisung

 

© 2005 PhaseTech, Inc.  All rights reserved.  

The CS-5 full range stereo custom installation loud-
speaker has been designed for easy in-wall or ceiling 
mounting.  Please read the instructions thoroughly before 
beginning and follow them step by step for a successful 
installation and years of listening pleasure.

Phase Technology warrants its loudspeakers to be free 
from defects in material and workmanship for a period of 
ten (10) years for speaker product and three (3) years for 
the electronic components to the original purchaser.  
Purchase must be made from an authorized Phase 
Technology dealer.

This warranty does not cover service or parts to repair 
damage caused by misuse, abuse, damage while in 
transit, alterations, unauthorized repairs, failure to follow 
instructions, fire, flood or any other cause beyond the 
reasonable control of Phase Technology.  Defects in 
speaker cabinets or grilles must be brought to the 
attention of your dealer immediately after purchase.  This 
warranty will be void if the products’ serial number has 
been altered or removed.

To obtain warranty service, defective product must be 
shipped in its original carton or equivalent together with 
original invoice or bill of sale, insured and prepaid to 
your authorized Phase Technology dealer or the factory 
when warranty service is requested.

If you choose to return the defective product to the 
factory you must first call us at (904) 777-0700 to 
obtain a Return Authorization number prior to shipping.  
Product repaired under this warranty will be returned to 
you freight collect.

Phase Technology will not pay for loss of time, 
inconvenience, loss of use, or property damage caused 
by your speaker product or its failure to work, or any 
other incidental or consequential damages.  Some states 
do not allow the exclusion or limitation of consequential 
damages, so the above limitation may not apply to you.

Phase Technology Corporation
6400 Youngerman Circle
Jacksonville, Florida   32244
(904) 777-0700  Telephone
(904) 771-7793  Fax

 When choosing a location for mounting the speakers, make 

certain the wall or ceiling material is sturdy enough to support the weight of the 
speakers.

  Decide where the speakers will be mounted.  Be careful not to 

 

mount them over a stud or any other obstruction and at least 

 

3/4” from the stud.

  It is recommended for maximum performance, although not 

 

necessary, that you place a piece of fiberglass or some similar 

 

dampening material behind the speaker.

  Be certain you can run the speaker wire to the point where the 

 

speaker will be mounted.  Phase Technology recommends 18

 

gauge for distances up to 15 feet and a minimum of 16 gauge for 

 

distances up to 50 feet.  For longer lengths or purer signal 

 

connections, consult your retailer.

  The grilles and baffle edge come in an off-white finish. Paint them using a  

 

good quality interior or exterior paint in the color of your choice. Place the  

 

grille in the baffle prior to painting. The cloth behind the grille will keep the  

 

paint from getting on the speakers. Use as light a coating as possible to  

 

avoid clogging the holes in the grille.

 

1. Using the template as a guide (inside package filler), carefully cut a 
hole in the wall or ceiling.  Find the speaker wire leads and pull them through.
 
2. Remove the grille from the speaker system.

3. Locate the speaker wire and attach it to the CI input terminals: red/plus, 
black/minus

4. If you are using any dampening material, secure it in the hole behind where 
the speaker will be located.

5. Place the speaker in the cut-out.

6. Turn the four locking screws counterclockwise one full turn to release the 
locking clamps.  Once released, turn them clock-wise until they firmly clamp the 
speaker to the mounting surface.

7. Position the grille on the baffle and firmly push it into the flange until you feel 
it is securely in position.

8. The speaker system is now ready to be turned on.

9. For removal of the custom installation speaker remove the grille.  Turn the 
four locking screws counterclockwise until they release from the wall or ceiling.  
Then pull the system out and disconnect the speaker wires.