Brother HL-3260N Anleitung Für Quick Setup
I
ON
O
OFF
I
ON
O
OFF
Step 1 Unpack the Printer
Step 2 Install the Toner Bottle
Step 3 Load paper into the paper tray
Step 4 Print test page
Quick Setup Guide
Laser Printer HL-3260N
Continue to the reverse side.
1
Lift the green handle.
1
Slide the paper tray out.
1
Set the paper sensor.
2
Make sure that the printer power switch is off.
Connect the AC power cord to the printer.
Do not connect the interface cable.
Connect the AC power cord to the printer.
Do not connect the interface cable.
3
Plug the AC power cord into an AC outlet.
Turn the power switch on.
Turn the power switch on.
4
After the printer has finished warming up, the
READY message appears.
READY message appears.
5
Press the Go switch. The printer prints a test page.
Check that the test page has printed correctly.
Check that the test page has printed correctly.
Note: When you want to set the
Control Panel message language,
refer to the Control Panel section on
the reverse side of this sheet.
Control Panel message language,
refer to the Control Panel section on
the reverse side of this sheet.
2
Make sure the side guide lock lever
is set to the "unlocked" position.
is set to the "unlocked" position.
3
While pressing the release lever of
the side guide (1), slide the side
guide wide open (2).
the side guide (1), slide the side
guide wide open (2).
4
Align the right side of the paper stack
and load it into the paper tray.
and load it into the paper tray.
5
While pressing the release lever of
the side guide (1), align the side
guide for the loaded paper size (2).
the side guide (1), align the side
guide for the loaded paper size (2).
6
Set the side guide lock to the
"locked" position.
"locked" position.
7
While pushing the release lever of
the rear guide (1), align the rear
guide for the loaded paper size (2).
the rear guide (1), align the rear
guide for the loaded paper size (2).
8
Adjust the paper size dial to match the
loaded paper size (1).
Slide the paper tray into the printer (2).
loaded paper size (1).
Slide the paper tray into the printer (2).
2
While pushing the green lever down (1), hold
the handle and slide the toner holder out
slightly (2).
the handle and slide the toner holder out
slightly (2).
3
Release the green lever and slide the
toner holder out gently until it stops.
toner holder out gently until it stops.
4
Rock the toner bottle gently several
times (1), and remove the black lid (2).
times (1), and remove the black lid (2).
5
Put the toner bottle in the toner holder (1),
then push the top of the bottle downwards to
lock it in place (2).
then push the top of the bottle downwards to
lock it in place (2).
6
Slide the toner holder into the printer until
it clicks into place and then push the
green handle down.
it clicks into place and then push the
green handle down.
7
Close the front cover.
1
Remove the tapes.
2
Slide paper tray 2 out.
3
Release the side guide lock lever (1) and then
slide the side guide while pressing the release
lever (2).
slide the side guide while pressing the release
lever (2).
4
Remove the tape and the
cardboard.
cardboard.
5
Take the toner bottle out of paper
tray 2.
tray 2.
6
Slide paper tray 1 out.
7
Repeat Steps
3
and
4
above on
paper tray 1.
8
Slide paper tray 1 and 2 into the printer
until they stop.
until they stop.
9
Open the front cover.
10
Remove the red tag, the metal
fitting and the two tags.
fitting and the two tags.
Set up the printer
Carton components
Carton components may differ from one country to another.
Save all packing materials and the printer carton. They should be used when shipping the printer.
Save all packing materials and the printer carton. They should be used when shipping the printer.
Printer
Drum
(pre-installed)
(pre-installed)
AC power cord
Documents
Toner
(in Paper tray 2)
(in Paper tray 2)
CD-ROM
Tray number seal
Up to here
Read the "Safety Sheet" first to ensure that you use this printer safely.
Read this "Quick Setup Guide" before you set up the printer.
Before you can use the printer, you must set up the hardware and install the driver.
Read this "Quick Setup Guide" before you set up the printer.
Before you can use the printer, you must set up the hardware and install the driver.
Identify the operating system on your computer (Windows
®
95 / 98 / Me, Windows NT
®
4.0,
Windows
®
2000 or Macintosh
®
).
The interface cable is not a standard accessory. Please purchase the appropriate interface
cable for the interface you intend to use (parallel or Network). Most existing parallel cables
support bi-directional communication, but some might have an incompatible pin assignment
or may not be IEEE 1284 compliant.
Follow the instructions in this guide for your operating system and interface.
cable for the interface you intend to use (parallel or Network). Most existing parallel cables
support bi-directional communication, but some might have an incompatible pin assignment
or may not be IEEE 1284 compliant.
Follow the instructions in this guide for your operating system and interface.
side guide
lock lever
lock lever
toner bottle
red tag
side guide
release lever
paper tray 2
paper tray 1
front cover
green
handle
handle
toner bottle
toner holder
green lever
lid
release lever
rear guide
paper size dial
LJ2343001 Printed in Japan
PRINTING
READY
paper sensor