Cleveland cr-28 Betriebsanweisung
Operator’s Manual
Rotisserie Oven
20
Error Messages
Display
Cause
Remedy
Or
This three-part message (plus alarm) is
displayed when the controller detects that
the oven temperature probe is shorted, or
that the oven temperature is not rising, or is
rising too slowly.
displayed when the controller detects that
the oven temperature probe is shorted, or
that the oven temperature is not rising, or is
rising too slowly.
Turn off the alarm by pressing any button
on the control panel.
on the control panel.
Open the door to check if there is any heat
at all. If there’s no heat, either the probe is
open and the burners are kept off by the
controller, or the gas supply is turned off,
which you should check. If there is some
heat check that the gas valve is fully open.
If the gas is OK, then the problem will
require service.
at all. If there’s no heat, either the probe is
open and the burners are kept off by the
controller, or the gas supply is turned off,
which you should check. If there is some
heat check that the gas valve is fully open.
If the gas is OK, then the problem will
require service.
The controller has detected an overcurrent
condition in the rotisserie drive motor. The
alarm tone will sound continuously.
condition in the rotisserie drive motor. The
alarm tone will sound continuously.
The only way to turn off the alarm is to turn
power off to the oven and turn it back on.
Check for some obstruction of the drive
system. Call service if the error does not
go away.
power off to the oven and turn it back on.
Check for some obstruction of the drive
system. Call service if the error does not
go away.
A power loss of more than 5 minutes will
sound the alarm tone and display this
message. Press any button to cancel the
alarm.
sound the alarm tone and display this
message. Press any button to cancel the
alarm.
A power loss of 5 minutes or less will not
sound the alarm or show this message.
When power returns, the cooking cycle will
resume where it left off. A longer loss will
cause the oven to reset and enter the
Preheat/Ready mode.
sound the alarm or show this message.
When power returns, the cooking cycle will
resume where it left off. A longer loss will
cause the oven to reset and enter the
Preheat/Ready mode.
This message is displayed (with alarm) if
the oven temperature probe fails open. If
the open condition goes away before 20
seconds, the oven will return to its previous
state; however, the alarm must be turned off
by pressing the TEMP button
the oven temperature probe fails open. If
the open condition goes away before 20
seconds, the oven will return to its previous
state; however, the alarm must be turned off
by pressing the TEMP button
If the probe remains open, call for service.
This message is displayed upon power up if
the controller detects a fault within one of
the Menu Item programs, or if new controller
software has been installed. Press any
button to acknowledge the message.
the controller detects a fault within one of
the Menu Item programs, or if new controller
software has been installed. Press any
button to acknowledge the message.
This is not an error message. It is displayed
when you are attempting to review a Menu
Item button which has not been
programmed.
when you are attempting to review a Menu
Item button which has not been
programmed.
These are not error messages. They are
displayed upon power up of the oven,
when the software is initializing. The “New
Version” message is shown when new
software is detected for the first time.
displayed upon power up of the oven,
when the software is initializing. The “New
Version” message is shown when new
software is detected for the first time.
Shorted
Probe
Probe
Faulty
Heater
Heater
Over
Current
Current
Power
Loss
Loss
Probe
Open
Open
Checksum
Error
Error
Unused
Item
Item
System
Init
Init
System
Init
Init
New
Version
Version
Version
CR xx.xx
CR xx.xx