Sherwood rd-8108 Betriebsanweisung
ENGLISH
1 2
USING FUNCTIONS OF REMOTE
Entering a setup code
• This remote control can control up to 8 different components.
• Before operating audio and video components other than this receiver with using this remote control, the setup
• Before operating audio and video components other than this receiver with using this remote control, the setup
code for each component should be entered.
• For system remote control operation, “000” was stored previously in the memory of the device button “CD” for
Sherwood CD player, “DVD” for Sherwood DVD player and “AUX” for Sherwood tape deck respectively as its
factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case
that its code does not work.
factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case
that its code does not work.
Find the setup codes according to the type
and the brand name of your component,
referring to “Setup Code Table” on page 37.
and the brand name of your component,
referring to “Setup Code Table” on page 37.
2
Turn on the component you want to control
1
Enter a 3 digit code, aiming the remote control
at the remote sensor on the component.
Example) When entering “001”.
at the remote sensor on the component.
Example) When entering “001”.
4
• The LED will flicker once.
Note:
• The AUDIO button is unavailable for the audio
• The AUDIO button is unavailable for the audio
components other than this receiver.
• If entering is performed successfully, the LED will
flicker twice.
• To be sure that the setup code is correct, press the
POWER(or STANDBY) button.
If your component is tuned off, the setup code is correct.
• When your component is not turned off, repeat the
above steps 2 to 4, trying each code for your
component until you find one that works.
component until you find one that works.
Notes:
• If the LED did not flicker twice, then repeat the above
• If the LED did not flicker twice, then repeat the above
steps 3 to 4 and try entering the same code again.
• Manufacturers may use different setup codes for the
same product category. For that reason, it is important
that you check to see if the code you have entered
operates as many controls as possible. If only a few
functions operate, check to see if another code will
work with more buttons.
that you check to see if the code you have entered
operates as many controls as possible. If only a few
functions operate, check to see if another code will
work with more buttons.
• When operating a Sherwood CD player or tape deck
using the system remote control, aim the remote
control at the REMOTE SENSOR on this receiver.
control at the REMOTE SENSOR on this receiver.
However, in case of Sherwood DVD player and MD
recorder, aim it at the REMOTE SENSOR on the
corresponding component.
recorder, aim it at the REMOTE SENSOR on the
corresponding component.
Press and hold down both the ENTER
button and the DEVICE button you want
for more than 1 second.
button and the DEVICE button you want
for more than 1 second.
3
Repeat the above steps 1 to 4 for each of
your components.
your components.
5
AUTO
1
2
3
4
5
6
7
8
9
0
T.TONE
DSP
STEREO
POWER
AUDIO
VCR
SPK SET
ADJUST
M1
M2
M3
AUDIO SEL.
OSD
SETUP
SLEEP
DISPLAY
DIMMER
RETURN
P.SCAN
TUNER
CD
AUX
VIDEO1 VIDEO2 VIDEO3
TAPE
7CH DIR.
+10
TUNE
PRESET
ENTER
SUBTITLE
ZOOM
VOLUME
MUTE
CH SEL.
CH/LEVEL
MACRO
DVD
CABLE
SAT
CD
AUX
TV
STANDBY
PL
PARA.
MENU
UNIVERSAL REMOTE CONTROL
RNC-40
ENTER
CD
AUX
TV
VCR
DVD
CABLE
SAT
: For CD player
: For tape deck, LD player, etc.
: For TV
: For VCR
: For DVD player
: For cable box
: For satellite receiver
AUTO
1
2
3
4
5
6
7
8
9
0
T.TONE
DSP
STEREO
POWER
AUDIO
VCR
SPK SET
ADJUST
M1
M2
M3
AUDIO SEL.
OSD
SETUP
SLEEP
DISPLAY
DIMMER
RETURN
P.SCAN
TUNER
CD
AUX
VIDEO1 VIDEO2 VIDEO3
TAPE
7CH DIR.
+10
TUNE
PRESET
ENTER
SUBTITLE
ZOOM
VOLUME
MUTE
CH SEL.
CH/LEVEL
MACRO
DVD
CABLE
SAT
CD
AUX
TV
STANDBY
PL
PARA.
MENU
UNIVERSAL REMOTE CONTROL
RNC-40
0
0
1
TUNER