Dwin transvision Betriebsanweisung
- 7 of 23 -
The RGBS1 and RGBS2 inputs are provided for HD (480p, 580p, 720p, 1080i ) sources and computer
graphics with VGA, SVGA, and XGA resolution. For computer graphics with VGA, SVGA, or XGA, it is
recommended to set the computer to 60 Hz vertical frequency.
graphics with VGA, SVGA, and XGA resolution. For computer graphics with VGA, SVGA, or XGA, it is
recommended to set the computer to 60 Hz vertical frequency.
For these inputs, the system provides source switching, converts H & V Sync to composite Sync,
provides control of contrast and brightness, and amplifies RGB video signals to allow the use of longer
cable lengths.
provides control of contrast and brightness, and amplifies RGB video signals to allow the use of longer
cable lengths.
The following are the pin assignments for the 15 PIN "D" connector:
1. Red
2. Green
3. Blue
13. Horizontal Sync
14. Vertical Sync
6-9. Ground
2. Green
3. Blue
13. Horizontal Sync
14. Vertical Sync
6-9. Ground
4. RS-232 COMPUTER INPUT
The RS-232C serial interface is provided for external control of the TransVision™ from a central
controller, such as a Home Theater control computer, Smart Home automation system, etc.
controller, such as a Home Theater control computer, Smart Home automation system, etc.
For DB9 connector pin-out and RS232 command list, please refer to “TransVision™ RS232 Control”
section.
section.
5. S-VIDEO INPUTS (S1, S2)
The S1 and S2 inputs are provided for NTSC (480i) or PAL (580i) video sources, such as off-air tuners,
satellite systems, cable boxes, SVHS VCR and DVD players. S-Video inputs, instead of composite
video inputs, are recommended for use with DVD players and satellite systems.
satellite systems, cable boxes, SVHS VCR and DVD players. S-Video inputs, instead of composite
video inputs, are recommended for use with DVD players and satellite systems.
For these inputs, the system provides source switching, contrast, brightness, color, tint and sharpness
controls, and amplifies S-video signals to allow the use of longer cable lengths.
controls, and amplifies S-video signals to allow the use of longer cable lengths.
6. COMPOSITE VIDEO INPUTS (V1, V2)
The V1 and V2 inputs are provided for NTSC (480i) or PAL (580i) video sources, such as off-air tuners,
satellite systems, cable boxes, VCR and DVD players.
satellite systems, cable boxes, VCR and DVD players.
For these inputs, the system provides source switching, contrast, brightness, color, tint and sharpness
controls, and amplifies video signals to allow the use of longer cable lengths.
controls, and amplifies video signals to allow the use of longer cable lengths.
7. COMPONENT VIDEO INPUTS (Y-Cr-Cb)
Three component video Y, Cr, Cb inputs are provided for interlaced component video signals from
regular DVD players (480i, 580i), progressive component video signals from progressive DVD players
(480p, 580p), and progressive or interlaced HD signals (480p, 540p, 720p, 1080i) from HD sources.
The TransVision™ determines which type of component video signal is applied to its input and
processes it accordingly.
regular DVD players (480i, 580i), progressive component video signals from progressive DVD players
(480p, 580p), and progressive or interlaced HD signals (480p, 540p, 720p, 1080i) from HD sources.
The TransVision™ determines which type of component video signal is applied to its input and
processes it accordingly.
For these inputs, the system provides source switching, contrast, brightness and color controls, and
amplifies video signals to allow the use of longer cable lengths.
amplifies video signals to allow the use of longer cable lengths.
8. AC POWER RECEPTACLE
The AC power receptacle should be connected to a non-switched 120 VAC outlet using the power cord
provided with the TransVision
provided with the TransVision
™
system.