Clavia c1 Betriebsanweisung

18

This section contains detailed guides on how to quickly 
set-up your instrument to match various conditions.

Connect a MIDI cable between MIDI OUT of your bass ped-
al unit and 

BASS PEDAL

 input.

• All MIDI messages will be received via the 

BASS PEDAL

 

input regardless of MIDI channel setting.

• MIDI messages received via the 

BASS PEDAL

 input is sent 

on the 

BASS MIDI CHANNEL

 via 

MIDI OUT

.

• MIDI messages will be received on the 

BASS MIDI CHAN-

NEL

 via 

MIDI IN

.

• Local Control settings apply to devices connected via 

the 

BASS PEDAL

 input.

The Half Moon Switch is an accessory item and sold sepa-
rately. When set to Half Moon Switch operation, the 

ROTA-

RY SPEAKER

 buttons on the front panel, as well as Rotary 

Speed Continuous Controller messages received via 

MIDI 

IN 

are disabled.

1

Mount the Half Moon Switch following the 
included instructions.

2

Connect the Half Moon Switch to the 

ROTARY 

CONTROL

 input

3

Press 

SHIFT 

+

 SYSTEM

 to enter the System Menu

4

Navigate with the PAGE/MENU buttons to 
page 7

5

Change setting

Press 

SHIFT

 + 

PAGE/MENU

 buttons and change setting 

to “

HA”

6

Press SYSTEM / MIDI / SOUND buttons to exit 
menu

If you encounter the sustain or rotary control pedal operat-
ing “backwards” you can adjust the pedal polarity in the 
System Menu.

1

Press 

SHIFT 

+

 SYSTEM

 to enter the System Menu

2

Navigate with the PAGE/MENU buttons

For adjusting the sustain pedal, navigate to page 5.

For adjusting the rotary pedal, navigate to page 7.

3

Change setting

Press 

SHIFT

 + 

PAGE/MENU

 buttons to change setting.

4

Press SYSTEM / MIDI / SOUND buttons to exit 
menu

As expression pedals from different manufacturers have 
various span characteristics, you can select span preset in 
the System Menu. 

1

Press 

SHIFT 

+

 SYSTEM

 to enter the System Menu

2

Navigate with the PAGE/MENU buttons to 
page 9

3

Change setting

Press 

SHIFT

 + 

PAGE/MENU

 buttons to change setting.

If the manufacturer of your pedal is not listed above, 
you can try operating the pedal to it’s end positions. 
The pedal range is briefly shown in the 

DISPLAY

 as a 

value between 0 and 100. Select the setting that best 
match the range of your pedal.

Since both manuals send MIDI data on separate MIDI chan-
nels, it is possible to connect an external sound source and 
control it from one manual while playing internally on the 
other.

Follow the steps below as necessary:

1

Connect 

MIDI OUT

 to MIDI in on the external 

device

2

Match MIDI channels 

Match the MIDI channel setting of the manual you 
want to use with your external device. Please refer to 
“The MIDI Menu” on page 15 for detailed instructions.

• MIDI channel setting 1 - 16 uses the fast trigger key-

board response which result in MIDI note messages 
being sent with fixed velocity data. 

• MIDI channel setting E1 - E9 uses normal trigger 

response which result in velocity variable data being 
sent via 

MIDI OUT

. Fast trigger response is still used 

internally.

3

Set MIDI CC Mode to “Off”

Normally all buttons and knobs send MIDI continuous 
controller data, which can lead to undesirable results 
when an external sound generator is connected.

This can be turned of by setting the MIDI CC Mode to 
“Off” or “Receive”. This is done in the MIDI menu. Please 
see “Continuous Controller mode” on page 16 for 
detailed instructions.

4

Set Sustain Pedal Mode

If you want the sustain pedal to operate the external 
device only, set the sustain pedal setting in the System 
menu to “

OF

”. Please refer to “Sustain Pedal” on page 15 

for detailed instructions.

FA

Fatar

ER

Ernie Ball

YA

Yamaha

RO

Roland