Frigidaire glcs378dsa Installationsanweisungen
1
30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
(Models with an Electric Oven and a Gas Cooktop)
G. Minimum Cutout Depth is increased to 24" (61 cm) with backguard.
1 1/8"
(2.86 cm)
FRONT
OF
CABINET
G
Ref.
Ref.
NOTE: Wiring diagram for these appliances are enclosed in this booklet.
INSTALLATION AND SERVICE MUST BE PERFORMED BY
A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or death.
FOR YOUR SAFETY:
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•
If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.
P/N 318201661 (0305) Rev. A
English – pages 1-11
Español – páginas 12-22
Wiring Diagrams - pages 23-24
Do not pinch the power supply cord or the flexible gas conduit
between the range and the wall.
between the range and the wall.
Do not seal the range to the side cabinets.
**NOTE: 30" (76.2 cm) minimum clearance between the
cooktop and the bottom of the cabinet when the bottom of
wood or metal cabinet is protected by not less than ¼" (0.64
cm) flame retardant millboard covered with not less than No. 28
MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6
mm) aluminum, or 0.020" (0.5 mm) copper.
cooktop and the bottom of the cabinet when the bottom of
wood or metal cabinet is protected by not less than ¼" (0.64
cm) flame retardant millboard covered with not less than No. 28
MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6
mm) aluminum, or 0.020" (0.5 mm) copper.
36" (91.4 cm) minimum clearance when the cabinet is
unprotected..
unprotected..
22 7/8"*
(58.1 cm) min.
23 1/4"*
(59.05 cm) max.
* For cutouts below 22 7/8", appliance
will slightly show out of the cabinet.
Regulator
• Door Open
(see note)
B
C
A
21 3/4"
(55.5 cm)
1 5/16"
(3.33 cm)
• NOTE: Allow at
least 19 ¼" (48.9 cm)
clearance for door
least 19 ¼" (48.9 cm)
clearance for door
35 3/8" (90 cm)
36 3/8" (92 cm)
36 3/8" (92 cm)
30"
(76,2 cm)
28 5/16"
(71,9 cm)
(71,9 cm)
30"
(76,2 cm)
21 3/4" (55,2 cm) Min.
22 1/8" (56,2 cm) Max.
36" (91,4 cm) standard
35 3/8" (90 cm) min.
35 3/8" (90 cm) min.
A. HEIGHT
B.WIDTH
C. DEPTH
TO FRONT
OF RANGE
F. MINIMUM
CUTOUT
WIDTH
G. CUTOUT
DEPTH
H. HEIGHT
OF
COUNTERTOP
.
WALL
1 ½" Max.
(3.8 cm Max.)
10" Min.
(25.4 cm
Min.)
From Wall
Both Sides
30" Min.
(76.2 cm Min.)
30" Min.**
(76.2 cm Min.**)
18" Min.
(45.7 cm) Min.
24" Min.
(61 cm Min.)
Approx. 1 7/8"
(4.8 cm)
Grounded Jonction Box or Wall
Outlet Should Be Located 8" to
17" (20.3 cm to 43.2 cm) From
Right Cabinet and 2" to 4" (5.1
cm to 10.2 cm) From Floor.
Locate Cabinet
Doors 1" (2.5
cm) Min.
from Cutout
Opening.
Doors 1" (2.5
cm) Min.
from Cutout
Opening.
G
H
F
31 1/2"
(81 cm)
Exact
13"
(33 cm)
Shave Raised Edge
to Clear
31 1/2" (81 cm)
Wide Cooktop Rim.
to Clear
31 1/2" (81 cm)
Wide Cooktop Rim.
* Note: For 29" (73.7
cm) cutout wide
opening, you must call
for optional side
panels and clear wide
cooktop rim as shown
in the "Countertop
Preparation" section
(see page 6).
cm) cutout wide
opening, you must call
for optional side
panels and clear wide
cooktop rim as shown
in the "Countertop
Preparation" section
(see page 6).