Panasonic AJ-HPX2000 Benutzerhandbuch

42

Adjustments and Settings for Recording : Multi Format

The unit employs a progressive scan (full pixel reading) CCD system.
With combinations of the SYSTEM MODE and CAMERA MODE menu options on the SYSTEM MODE screen on the 

SYSTEM SETTING menu, you can select an image system from among 23 types*

1

 including HD (1080i, 720P) and SD 

formats.
In any image system, the CCD operates in progressive (non-interlace) scan mode.

 In addition, through the REC SIGNAL 

menu option, you can record external input signals such as 1394 and SDI (optional).
*1

 When the AVC-Intra codec board (AJ-YBX200G, optional) is installed

Allows you to select a combination of system
frequency (59.94 Hz or 50 Hz) and signaling system
(1080i, 720P, 480i, or 576i). When a change has been
made to the SYSTEM MODE option, the viewfinder
indicates “TURN POWER OFF.” Then, turn the
POWER switch of the camera-recorder off and wait
five seconds or longer before turning the camera-
recorder on again.

Signals from the camera are recorded. The
CAMERA MODE option allows you to select
a camera operation mode (frame mode).

Signals from the DVCPRO/DV connector are
recorded. For information about the 1394
connection, see [Connection through the
DVCPRO/DV connector] (page 129).

Signals from the GENLOCK IN connector
are recorded when the camera-recorder is in
SD mode (480-59.94i or 576-50i).

Signals from the SDI IN connector are
recorded (when the AJ-YA350AG, an SDI IN
option, is installed).

‹

z When VIDEO is selected, video may produce noise

if the signals from GENLOCK IN are non-standard
signals.

z When SDI is selected, the time code or UMID

superimposed on SDI input signals are not
recorded.

Used to select a camera operation mode when the
option REC SIGNAL is set to CAM. For information
about the behavior for each setting, see [Recording
formats and output connector signal formats

‹

When the camera has been switched from 60i, 60P, or
30P to 24P or 24PA, video may produce noise for a
moment because the pull-down five-frame cycle is
adjusted. This is not an abnormal condition.

Used to select the recording mode

The DVCPRO HD format is used to record 
video. The pull-down recording is for the 30P, 
24P, 24PA and 25P modes.

The native mode used to record video in 
DVCPRO HD format. (Only for 720P)

（when the AVC-Intra codec board is 

installed

）

The AVC-Intra50 format is used to record 
video. The native recording is applied to the 
30P, 24P and 25P modes.

（when AVC-Intra codec board is installed)）

The AVC-Intra100 format is used to record 
video. The native recording format applies to 
the 30P, 24P and 25P modes.

‹

When AVC-Intra 50 or AVC-Intra 100 is selected, the
24PA mode cannot be selected.

The DVCPRO50 format (50 Mbps) is used to
record video.

The DVCPRO format (25 Mbps) is used to
record video.

The DV format is used to record video.

Used to select the aspect ratio for the SD mode (480i
or 576i)

：9

The 16:9 aspect ratio is used to record video.

：3

The 4:3 aspect ratio is used to record video.

Video system and Recording format

Selecting a recording signal and method

Multi Format

AJ-HPX2000P(VQT1D27-1)E.book  42 ページ  ２００７年７月３０日　月曜日　午後１時３１分