Panasonic aj-sdx900 Benutzerhandbuch
31
4
Chapter 4 Adjustments and settings for recording
Tape continuity with the user’s bit
Selecting REGEN for the UB MODE item on the <TC/UB>
screen by performing menu operations will call up the user’s
bit recorded on the tape, making it possible to continue
recording from that value. However, it is not possible to record
the contents that were set.
screen by performing menu operations will call up the user’s
bit recorded on the tape, making it possible to continue
recording from that value. However, it is not possible to record
the contents that were set.
<Note>
The time code/user’s bit are also recorded in the VIDEO AUX
area of the unit’s memory. The time code (VITC) is the same
value as the sub code area’s time code (LTC).
Special information such as the camera’s frame rate is
recorded in the user’s bit (VITC’s user’s bit).
The time code/user’s bit are also recorded in the VIDEO AUX
area of the unit’s memory. The time code (VITC) is the same
value as the sub code area’s time code (LTC).
Special information such as the camera’s frame rate is
recorded in the user’s bit (VITC’s user’s bit).
4-5
Setting the time data
The time code setting range extends from 00:00:00:00 to
23:59:59:29.
23:59:59:29.
4-5-1
Setting the user’s bit
Memos and other information with up to 8 digits (dates, times)
in hexadecimal notation can be recorded on the sub code
track by setting the user’s bit.
in hexadecimal notation can be recorded on the sub code
track by setting the user’s bit.
1
Set the DISPLAY switch to UB.
2
Set the TCG switch to SET.
4
Set the TCG switch to F-RUN or R-RUN.
5
Open the <TC/UB> screen from the VTR MENU page
and select USER as the UB MODE item setting by
performing menu operations.
and select USER as the UB MODE item setting by
performing menu operations.
3
Set the user’s bit using the SHIFT button, UP (+) button
and DOWN (–) button.
SHIFT button:
and DOWN (–) button.
SHIFT button:
This is used to cause the digit that is
to be set to flash. Each time it is
pressed, the flashing digit moves to
the right.
to be set to flash. Each time it is
pressed, the flashing digit moves to
the right.
UP (+) button:
This increments the numerical value
of the flashing digit by 1.
of the flashing digit by 1.
DOWN (–) button: This decrements the numerical value
of the flashing digit by 1.
DISPLAY switch
Display window
TCG switch
DOWN (–) button
UP (+) button
HOLD switch
4-4-3
CH3 and CH4 recording levels
When the unit is going to be used in the DVCPRO50 format,
audio signals can be recorded separately for four audio
channels. Perform menu operations to open the <MIC/
AUDIO1> screen from the VTR MENU page to change the
settings for the AUTO LEVEL CH3 and AUTO LEVEL CH4.
Depending on the setting conditions and input level for these
items, recording levels for audio tracks CH3 and CH4 change
as shown in the table below. Note that adjustments cannot be
performed manually.
audio signals can be recorded separately for four audio
channels. Perform menu operations to open the <MIC/
AUDIO1> screen from the VTR MENU page to change the
settings for the AUTO LEVEL CH3 and AUTO LEVEL CH4.
Depending on the setting conditions and input level for these
items, recording levels for audio tracks CH3 and CH4 change
as shown in the table below. Note that adjustments cannot be
performed manually.
AUTO LEVEL
CH3/CH4*
ON
AGC ON
AGC ON
Input level
LINE
MIC
OFF
AGC/LIMITER OFF
LIMITER ON
<Note>
When the DVCPRO format (25 Mbps) has been set, the audio
signals will be recorded on two channels (CH1 and CH2) only.
The same signals as for CH1 and CH2 are also output to the
SDI output CH3 and CH4 channels.
When the DVCPRO format (25 Mbps) has been set, the audio
signals will be recorded on two channels (CH1 and CH2) only.
The same signals as for CH1 and CH2 are also output to the
SDI output CH3 and CH4 channels.
VITC’s user’s bit
¢¢
:04:24:8¢
Checking
information
for the 6 digits
at right.
information
for the 6 digits
at right.
Tape management information
≥
Renew frame flag
≥
REC START/STOP mark
Camera shooting mode
60i:
600
30P:
308
24P:
248
24PA:
24C
Fixed
value
value
User’s bit memory function
The user’s bit settings (except for the actual time) are
automatically saved in the memory and retained even after
the power is turned off.
automatically saved in the memory and retained even after
the power is turned off.
Sequence No.
24P, 24PA:
0 to 4
In all other modes:
Fixed at F