Panasonic aj-spc700 Benutzerhandbuch
67
5
Chapter 5 Preparation
(continued)
5-1-2 Use of the external DC power supply
1
Connect the external DC power supply to the DC IN
socket on the unit.
socket on the unit.
2
Turn ON the power switch of the external DC power
supply. (If the power switch is available on the external
DC power supply)
supply. (If the power switch is available on the external
DC power supply)
3
Turn ON the POWER switch on the unit.
<Notes>
z If both the battery pack and the external DC power
supply are connected, the electric power is supplied
from the external DC power supply. While the
external DC power supply is used, the battery can be
mounted and removed on/from the unit.
from the external DC power supply. While the
external DC power supply is used, the battery can be
mounted and removed on/from the unit.
z When the external DC power supply is used, ensure that
the power switch of the external DC power supply is
turned on first and then the POWER switch on the unit is
turned on. In the case of the reverse operation, a
malfunction may occur on the unit since the output
voltage of the external DC power supply is raised slowly.
turned on first and then the POWER switch on the unit is
turned on. In the case of the reverse operation, a
malfunction may occur on the unit since the output
voltage of the external DC power supply is raised slowly.
z When connecting a battery to the DC IN socket,
select the battery type listed under EXT DC IN
SELECT. Select EXT DC IN SELECT from the
<BATTERY/P2CARD> screen on the MAIN
OPERATION page. In this case, however, the %
display is disabled, even when using a digital battery.
SELECT. Select EXT DC IN SELECT from the
<BATTERY/P2CARD> screen on the MAIN
OPERATION page. In this case, however, the %
display is disabled, even when using a digital battery.
5-2 Mounting the Viewfinder and
Adjusting its Position
Please refer to the viewfinder instruction manual.
Note: A slide rail is required to mount any viewfinder other
than models AJ-VF15B or AJ-VF20WB.
Note: A slide rail is required to mount any viewfinder other
than models AJ-VF15B or AJ-VF20WB.
z If you need to buy a slide rail, please contact the store
where you purchased the camera-recorder and tell them
that the slide rail is a “repair part”.
that the slide rail is a “repair part”.
Slide rail (VFC3995)
Screws (XBS3+8VZ)
Screws (XBS3+8VZ)
Mounting the Slide Rail
1
Undo the upper two screws for AJ-VF15 or AJ-VF20W,
and remove the mounting unit.
Leave the screws attached to the mounting unit.
and remove the mounting unit.
Leave the screws attached to the mounting unit.
2
Mount the slide rail, then tighten the two screws.
DC IN Socket
External DC
power supply
power supply
Rush current may occur at the time for turning on the
power of the unit. We recommend using an external DC
power supply capable to secure double or more
capacity of the total power consumption of the devices
connected to the unit such as the viewfinder and lights.
Use a DC cable with a capacity of 10A or more.
power of the unit. We recommend using an external DC
power supply capable to secure double or more
capacity of the total power consumption of the devices
connected to the unit such as the viewfinder and lights.
Use a DC cable with a capacity of 10A or more.
Confirm the pin arrangements of the DC output connector
of the external DC power supply and the DC IN socket on
the unit, and connect the proper polarities to each other.
If the +12 V power supply is connected to the GND
connector in error, it may cause a fire or failure of the unit.
of the external DC power supply and the DC IN socket on
the unit, and connect the proper polarities to each other.
If the +12 V power supply is connected to the GND
connector in error, it may cause a fire or failure of the unit.
1
2
3
4
Pin No.
Signal
1
GND
2, 3
—
4
+12V
DC IN Socket
Mounting unit
Screws
Slide rail
#,52%2
'PINKUJDQQMࡍࠫ㧞㧜㧜㧢ᐕ㧡㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ