Panasonic aj-spc700 Benutzerhandbuch
93
7
Chapter 7 Maintenance and Inspections
(continued)
6. Inspection of the clock, time code, and user bits
1
Set the user’s bit as required.
Please refer to [4-5-1 Setting the User Bits] for the
setting procedures.
Please refer to [4-5-1 Setting the User Bits] for the
setting procedures.
2
3
Set the TCG switch to [R-RUN].
4
Press the REC START/STOP button.
Check that the counter display number changes as
recording progresses.
Check that the counter display number changes as
recording progresses.
5
Press the REC START/STOP button again.
Check that recording stops and the counter display
number stops changing.
Check that recording stops and the counter display
number stops changing.
6
Set the TCG switch to [F-RUN].
Check that the counter display number changes
regardless of recording status.
Check that the counter display number changes
regardless of recording status.
7
Set the DISPLAY switch to [UB].
Each time the HOLD button is pressed, make sure that
the displayed value changes in the following sequence:
VTCG
Each time the HOLD button is pressed, make sure that
the displayed value changes in the following sequence:
VTCG
DATE TIME No display (time zone)
TCG; and also verify that the displayed value is correct.
If DATE, TIME, or time zone is not correct, refer to [4-5-
2 Setting the Internal Clock’s Date and Time] for
guidance on setting the correct values.
If DATE, TIME, or time zone is not correct, refer to [4-5-
2 Setting the Internal Clock’s Date and Time] for
guidance on setting the correct values.
<Note>
Note that date and time data set for DATE, TIME, and
time zone is recorded in clips, and affects the playback
sequence, etc. at the time of thumbnail manipulations.
time zone is recorded in clips, and affects the playback
sequence, etc. at the time of thumbnail manipulations.
7-2 Maintenance
7-2-1 Cleaning Inside the Viewfinder
z Do not use thinner or other solvents to remove dirt from
the viewfinder.
z Wipe the lens with a commercially available lens cleaner.
z Do not wipe the mirror. If dirt or rubbish is sticking on the
z Do not wipe the mirror. If dirt or rubbish is sticking on the
mirror, remove it with a commercially available air blower.
7-2-2 Phenomenon Inherent to CCD
Cameras
Smears
Smears may appear when shooting an object with very high
brightness.
This phenomenon may appear more frequently as the
electronic shutter speed increases.
brightness.
This phenomenon may appear more frequently as the
electronic shutter speed increases.
7-2-3 Replacing the Backup Battery
The camera is shipped from the factory with a backup
battery already mounted.
When the battery runs out, the [BACK UP BATT EMPTY]
display appears on the viewfinder screen for 5 seconds after
the power switch is turned ON.
The internal clock stops operating when the battery runs out.
Also, the TCG time code value returns to [00:00:00:00], and
the time code backup is disabled. The battery must be
replaced.
Please consult your distributor for replacement with a new
battery (CR2032).
The backup battery is visible when the panel on the LCD
monitor side is removed (right side when viewed from the
front).
battery already mounted.
When the battery runs out, the [BACK UP BATT EMPTY]
display appears on the viewfinder screen for 5 seconds after
the power switch is turned ON.
The internal clock stops operating when the battery runs out.
Also, the TCG time code value returns to [00:00:00:00], and
the time code backup is disabled. The battery must be
replaced.
Please consult your distributor for replacement with a new
battery (CR2032).
The backup battery is visible when the panel on the LCD
monitor side is removed (right side when viewed from the
front).
<Note>
Please contact the store where you purchased the camera
when replacing the battery.
when replacing the battery.
#,52%2
'PINKUJDQQMࡍࠫ㧞㧜㧜㧢ᐕ㧡㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ