Panasonic sdr-sw21 Benutzerhandbuch
24
VQT2A17
25
VQT2A17
Setup
2
Charging time, recordable time and
Remaining battery capacity indication
Charging time and recordable time
Times are given for a temperature of 25 ˚C (77 ˚F) and humidity of 60 %.
The charging time shown in the table are approximations. In high or low
temperatures, charging requires more time.
The charging time shown in the table are approximations. In high or low
temperatures, charging requires more time.
Supplied battery VW-VBJ10 (3.6 V, 940 mAh (minimum))
Charging time
Approx. 2 hours 15 minutes
Recordable time
Maximum continuously
recordable time
Actual recordable time
Approx. 1 hour 10 minutes
Approx. 40 minutes
Actual recordable time includes recording and stopping, power ON/OFF
switching, zooming and other operations.
Recordable time varies according to conditions of use. For example, the
recordable time shortens when the [POWER LCD] setting is on while
recording.
The recordable time shortens in some environments (i.e., low temperatures,
etc.), therefore it is recommended to charge a spare battery.
switching, zooming and other operations.
Recordable time varies according to conditions of use. For example, the
recordable time shortens when the [POWER LCD] setting is on while
recording.
The recordable time shortens in some environments (i.e., low temperatures,
etc.), therefore it is recommended to charge a spare battery.
Remaining battery capacity indication
The battery indication changes, as the remaining battery power decreases.
High
Low
Flashing (Charge battery.)
●
●
●
●
Setup
3
Inserting/Removing SD
cards
(sold separately)
SD cards are sold separately.
Preparations: Set the mode dial to [OFF].
Preparations: Set the mode dial to [OFF].
(Check that the status indicator is out.)
Inserting or removing an SD card with the power ON may
damage the unit and destroy data on the card.
damage the unit and destroy data on the card.
Place label upwards.
While the card access lamp is lit, reading, recording, playback, deletion
or other processing is being executed. Performing the following
operations while the lamp is lit may damage the SD card and its content
and the unit may not function properly.
or other processing is being executed. Performing the following
operations while the lamp is lit may damage the SD card and its content
and the unit may not function properly.
• Switching off power
• Removing battery or AC adaptor
• Opening card/battery door and removing SD card
• Rotating the mode dial
• Shaking or impacting the unit
• Disconnecting the USB cable
• Removing battery or AC adaptor
• Opening card/battery door and removing SD card
• Rotating the mode dial
• Shaking or impacting the unit
• Disconnecting the USB cable
Card access lamp
The access lamp is supposed to light up while rotating the dial to select
a mode. In this case, there is no problem.
a mode. In this case, there is no problem.
●
●
2
Insert/Remove the SD
card.
To insert:
Face the label upwards and slide
the card in straight until hearing it
catch.
To remove:
Press the center of the SD card and
pull the card out straight.
Face the label upwards and slide
the card in straight until hearing it
catch.
To remove:
Press the center of the SD card and
pull the card out straight.
•
•
1
Open the card/battery
door.
Lift the flap upright and turn it
counter-clockwise until it clicks for
unlocking and then open the door.
counter-clockwise until it clicks for
unlocking and then open the door.
3
Close the card/battery
door.
Close the door and turn the flap
clockwise to the locking position
and then push the flap back flat.
If the door does not close
completely, remove the SD card,
check its orientation and reinsert it
into the slot.
clockwise to the locking position
and then push the flap back flat.
If the door does not close
completely, remove the SD card,
check its orientation and reinsert it
into the slot.
•
•
It has been found that counterfeit battery packs which look very similar to the genuine
product are available to purchase in some markets. Some of these battery packs are
not adequately protected to meet the requirements of appropriate safety standards.
These battery packs may lead to fire or explosion. Please be advised that we are not
liable for any accident or failure occurring as a result of use of a counterfeit battery
pack. To ensure that safe products are used we would recommend that a genuine
Panasonic battery pack is used.
product are available to purchase in some markets. Some of these battery packs are
not adequately protected to meet the requirements of appropriate safety standards.
These battery packs may lead to fire or explosion. Please be advised that we are not
liable for any accident or failure occurring as a result of use of a counterfeit battery
pack. To ensure that safe products are used we would recommend that a genuine
Panasonic battery pack is used.