Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Panasonic
  4. cn-nvd905
  5. Betriebsanweisung

Panasonic cn-nvd905 Betriebsanweisung

Download
Seite von 118
Check mounting and wiring
  GPS  information
Check GPS information reception.
1
Select [GPS Info] from the 
Information menu.
   The GPS Info screen is displayed.
2
Check the reception.
   Use a clearly visible point to check reception.
   Check that at least three satellite numbers 
are being received, and that the latitude and 
longitude are displayed.
Note:
   If GPS reception is not continuous, check connections 
to the GPS antenna, and its mounting position.
 Installation confi rmation
Check the state of mounting and wiring.
   Refer to the Installation Instructions for details.
1 Press 
.
   The Navigation menu is displayed.
2
Select [Information].
   The Information menu is displayed.
3
Select [Install. Status].
4
Check mounting.
   The items you can check are shown in the table 
on the right.
 The items you can check
 GPS Antenna
If the antenna is connected normally, 
this indicates “ON”.
 Lighting 
Switch
If the vehicle side lights are switched 
on, this changes to indicate “ON”.
 Reverse
When the shift lever is shifted to 
reverse, this changes to indicate “ON”.
 Parking Brake When the parking brake is pulled, this 
changes to indicate “ON”.
 Speed
Vehicle speed is displayed.
 ACC Voltage
The display should normally be 
approximately 12 V. (11 to 16 V)
 Speed Pulse
The reading changes to “0” when 
[Pulse Reset] is pressed. If the system 
is functioning normally, the number 
should be different after the vehicle 
has moved.
 Accuracy 
Level
The reading changes to “0” when 
[Level Reset] is pressed. The number 
changes after the vehicle has moved. 
(Level 4 is the maximum)
 Sensor Reset
The reading changes to uncorrected 
when [Sensor Reset] is pressed. 
Note:
   In the following situations, please reset “Speed Pulse”, 
“Accuracy Level” and “Sensor Reset”.
 
   The unit has been transferred to another vehicle.
 
   The tires have been changed.
 
   The tires have been rotated.
   On routes that involve congestion and frequent 
stop-start driving, such as in town, routes with many 
left and right turns, and routes where GPS signal 
reception is poor, the correction process could take a 
long time and leave errors in the stored content.
   For some vehicle models, the vehicle mark may stop 
moving when speed increases, but that does not 
indicate a malfunction when it takes place during the 
correction process.
 Installation  setting
Set the state of mounting and wiring.
   Refer to the Installation Instructions for details.
1
Select [Install. Setting] from the 
Information menu.
   The Install. Setting screen is displayed.
2
Make settings.
    Speed  Signal:
   Set the speed signal detection level. (It should 
be set to [Normal] in normal circumstances.)
Select [Low Level] if the voltage of the speed 
signal is low and the signal cannot be detected.
 default: 
[Normal]
    Rear  View  Camera:
   Set whether or not to switch to the 
image from the rear view camera when 
the shift lever is in the reverse position. 
(
 System Upgrade Guidebook) 
    [On]:   Set this if a rear view camera is 
connected. 
    [Off]:   Set this if no rear view camera is 
connected.
 default: 
[Off]
  Note:
 
    The image from the rear view camera may be 
blurred in the night or a dark place.
    H/F  Speaker:
   Set the speakers to use for audio output of 
hands-free conversation if a hands-free kit 
featuring Bluetooth
®
 technology (CY-BT100U, 
option) is connected.
  [Both]: 
  
Front 
Left/Right 
speaker
  [Lch]: 
  
Front 
Left 
speaker
  [Rch]: 
  
Front 
Right 
speaker
 default: 
[Both]
English
English
22
23
23
22