ENVISION en7100e Benutzerhandbuch
EN-7100e
4
31MY02
EN-7100e
For Your Safety
Special Notes on LCD Monitors
The following symptoms are normal with an LCD
monitor and do not indicate a problem:
monitor and do not indicate a problem:
•
Due to the nature of the fluorescent light, the
screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make
sure the flicker disappears.
screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make
sure the flicker disappears.
•
You may find slightly uneven brightness on the
screen depending on the desktop pattern you
use.
screen depending on the desktop pattern you
use.
•
The LCD screen has effective pixels of 99.99%
or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of
the time.
or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of
the time.
•
Due to the nature of the LCD screen, an after-
image of the previous screen may remain after
switching from an image that has been
displayed for hours. This after-image could
require several hours to disappear.
image of the previous screen may remain after
switching from an image that has been
displayed for hours. This after-image could
require several hours to disappear.
•
The life of the fluorescent light used in the LCD
monitor is approximately 20,000 hours. Contact
your dealer or EPI service center for
replacement when the screen is dark, flickering
or not lighting up. Never attempt to replace it by
yourself.
monitor is approximately 20,000 hours. Contact
your dealer or EPI service center for
replacement when the screen is dark, flickering
or not lighting up. Never attempt to replace it by
yourself.
General Notes
•
Do not install the monitor near heat sources
such as radiators or air ducts.
such as radiators or air ducts.
•
Do not place monitor in direct sunlight or in
areas with excessive dust, mechanical vibration
or shock.
areas with excessive dust, mechanical vibration
or shock.
•
Save the original shipping carton and packing
materials in case you need to ship your monitor.
Be sure to repackage your monitor as it was
originally packed at the factory.
materials in case you need to ship your monitor.
Be sure to repackage your monitor as it was
originally packed at the factory.
•
Periodically clean your monitor with a soft cloth.
Stubborn stains may be removed with a cloth
lightly dampened with a mild detergent solution.
Never use strong solvents such as thinners,
benzene, or abrasive cleaners, since these
will damage the cabinet. Always unplug the
monitor before cleaning it.
Stubborn stains may be removed with a cloth
lightly dampened with a mild detergent solution.
Never use strong solvents such as thinners,
benzene, or abrasive cleaners, since these
will damage the cabinet. Always unplug the
monitor before cleaning it.
Using the Right Power Cord
The supplied power cord is a NEMA 5-15 style
plug. It is UL-listed and CSA labeled for
125 volts AC.
plug. It is UL-listed and CSA labeled for
125 volts AC.
If the monitor will be connected to your computer’s
power outlet, use a minimum No. 18 AWG, type
SJT or SVT three conductors cord with one end
terminating with a male grounded plug, rated 10A,
250V, CEE-22. The other end must terminate with
a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female
configuration.
power outlet, use a minimum No. 18 AWG, type
SJT or SVT three conductors cord with one end
terminating with a male grounded plug, rated 10A,
250V, CEE-22. The other end must terminate with
a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female
configuration.