ONKYO ht-s870 Gebrauchsanleitung
52
Controlling Other Components
You can use the HT-R820THX’s remote controller (RC-
571M) to control your other AV components, including
those made by other manufacturers. To do this you first
need to enter the appropriate remote control code for
your DVD player, TV, VCR, cable receiver, or satellite
receiver. Then you need to select the corresponding
remote controller mode (see page 12).
571M) to control your other AV components, including
those made by other manufacturers. To do this you first
need to enter the appropriate remote control code for
your DVD player, TV, VCR, cable receiver, or satellite
receiver. Then you need to select the corresponding
remote controller mode (see page 12).
By entering the appropriate remote control code, the
[CD], [MD], and [CDR] mode buttons can also be used
with other manufacturer’s components (e.g., DVD, TV,
VCR, satellite or cable receiver).
[CD], [MD], and [CDR] mode buttons can also be used
with other manufacturer’s components (e.g., DVD, TV,
VCR, satellite or cable receiver).
Entering the appropriate remote control code for your
TV, VCR, and so on will allow you to control it with the
HT-R820THX’s remote controller. You’ll need to per-
form this procedure for each component that you want to
control.
TV, VCR, and so on will allow you to control it with the
HT-R820THX’s remote controller. You’ll need to per-
form this procedure for each component that you want to
control.
If the remote controller works as expected, the code has
been entered correctly. If not, try again or try another
code.
been entered correctly. If not, try again or try another
code.
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it’s connected via
depends on whether it’s connected via
, as follows:
5001:
Use this code if you’ve connected an
cable
and an analog audio cable (RCA) to your DVD
player. This is the default setting, so if you’re
using
player. This is the default setting, so if you’re
using
, you don’t need to change anything.
Point the remote controller at the
HT-R820THX to operate the DVD player.
HT-R820THX to operate the DVD player.
5002:
Use this code if your DVD player doesn’t have
an
an
socket, or you’re not using
. Point
the remote controller at the DVD player to
operate it.
operate it.
Resetting the [DVD], [CD], [MD] or [CDR]
Mode Button
By default, the [DVD], [CD], [MD] & [CDR] mode but-
tons are preprogrammed with remote control codes for
controlling Onkyo components connected via
tons are preprogrammed with remote control codes for
controlling Onkyo components connected via
. If
you’ve entered another code for a button and now want
to return to its default, perform the following procedure.
to return to its default, perform the following procedure.
Resetting the Remote Controller
This section explains how to reset the remote controller
to its default settings.
to its default settings.
Entering Remote Control Codes
1
Look up the remote control code for your
component.
component.
See “Remote Control Codes” on page 53.
2
While holding down the [DVD], [TV],
[VCR], [CABLE], [SAT], [CD], [MD], or
[CDR] mode button, press the [STANDBY]
button.
[VCR], [CABLE], [SAT], [CD], [MD], or
[CDR] mode button, press the [STANDBY]
button.
Remote indicator flashes twice.
3
Within 30 seconds, use the number but-
tons to enter the 4-digit remote control
code.
tons to enter the 4-digit remote control
code.
CD
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
V1
V2
V3
DVD
MULTI CH
--/---
TAPE
TUNER
INPUT
I
+
-
ENTER
SET
UP
GUI
DE
RE
TUR
EXIT
TO
P M
ENU
MEN
U
VOL
+
-
CDR
SAT
AMP
+
_
TV
VCR
CABLE
DVD
CD
MD
DISC
CH
TONE
TUNER/
TAPE
TAPE
TV
INPUT
INPUT
PREV
DIMMER
SLEEP
ON
STANDBY
T V
TV CH
T V VOL
REMOTE MODE
DVD, CD, MD,
CDR, TV, VCR,
CABLE, SAT
CDR, TV, VCR,
CABLE, SAT
TV
STANDBY
I
Number
buttons
buttons
Remote
indicator
indicator
4
Select the remote controller mode, point
the remote controller at the component,
and check its operation.
the remote controller at the component,
and check its operation.
Remote controller buttons that can be used in
DVD mode are shown on page 14. Those that can
be used with the TV, VCR, CABLE, and SAT
modes are shown on page 57.
DVD mode are shown on page 14. Those that can
be used with the TV, VCR, CABLE, and SAT
modes are shown on page 57.
1
While holding down the mode button that
you want to reset, press the TV [
you want to reset, press the TV [
] but-
ton.
Remote indicator flashes twice.
2
Press the mode button again.
The mode button is reset.
1
While holding down the [AMP] mode but-
ton, press the
ton, press the
[STANDBY] button.
Remote indicator flashes 5 times.
2
Press the [AMP] mode button again.
The remote controller is reset.
HT-S870_En.book Page 52 Monday, September 13, 2004 5:15 PM