Samsung mm-kt8 Gebrauchsanleitung
Timer Function
•
The timer enables you to switch the system on or off at specific times.
•
If you no longer want the system to be switched on or off automatically, you must cancel the timer.
•
Before setting the timer, check that the current time is correct.
•
For each step, you have a few seconds to set the required options.
If you exceed this time, you must start again.
If you exceed this time, you must start again.
Example:
You wish to wake up to music every morning.
•
ON TIME is displayed (instead
of the equalizer symbols) for a
few seconds, followed by any
switch-on time already set; you
can set the timer switch-on time.
of the equalizer symbols) for a
few seconds, followed by any
switch-on time already set; you
can set the timer switch-on time.
•
The source to be selected is
displayed.
displayed.
2
1
3
Switch the system
on by pressing
on by pressing
POWER
.
Press
TIMER/CLOCK
until
TIMER is
displayed.
Press the
ENTER
button.
•
is displayed to the top-right
of the time, indicating that the
timer has been set.
timer has been set.
•
The system will switch on and off
automatically at the required
times.
automatically at the required
times.
8
7
9
Press or button
to select the source to
be played when the
system switches on.
to select the source to
be played when the
system switches on.
Press
ENTER
to
confirm the timer.
Press
POWER
to
set the system to
standby mode.
standby mode.
5
4
a
. Set the hour by pressing or
button.
b.
Press
ENTER
.
•
The minutes flash.
c.
Set the minutes by pressing or
button.
button.
d.
Press
ENTER
.
•
OFF TIME is displayed (instead
of the equalizer symbols) for a few
seconds, followed by any switch-
off time already set; you can now
set the timer switch-off time.
of the equalizer symbols) for a few
seconds, followed by any switch-
off time already set; you can now
set the timer switch-off time.
•
TAPE (cassette) : Insert a cassette tape.
•
TUNER (radio) :
a
Press
ENTER
.
b
Select a preset station
by pressing
Tuning or .
by pressing
Tuning or .
•
CD (compact disc) : Load a compact
disc.
• USB
:connect the USB.
a
. Set the hour by pressing or
button.
b.
Press
ENTER
.
•
The minutes flash.
c.
Set the minutes by pressing or
button.
button.
d.
Press
ENTER
.
•
VOL 20 is displayed, where 20
corresponds to the volume
already set.
corresponds to the volume
already set.
Set the timer
switch-off time.
switch-off time.
6
Press or button
to adjust the volume
level and press
to adjust the volume
level and press
ENTER
.
Set the timer
switch-on time.
switch-on time.
Note
•
If the timer switch on and off times are identical, the word
ERROR is displayed.
64
MISCELLANEOUS
63
REMAIN
FAVORITE SONG
SEARCH SONG
TEMPO
KEY CONTROL
TUNER MEMORY
LOGO
TUNING MODE
SLOW
-
+
#
b
FEMALE
MALE
STEP
RESERVE
CANCLE
Selecting the cassette Playback
Mode/Repeat A
Mode/Repeat A
↔
B Function
•
Use this to listen to a specific section again during playback.
•
Set the start and end points of the section you want to repeat 3 times.
•
This is a useful when learning a foreign language.
•
The TAPE REPEAT function can be used only on sections that are longer
than 7 seconds.
than 7 seconds.
Press
REP. A
↔
B
button.
•
You cannot set the end point (B) within 7 seconds after
setting the start point (A).
setting the start point (A).
Note
REPEAT A
↔
B Function
•
When the display indicates...The micro component system plays back
One side of the selected cassette and then stops.
One side of the cassette.
The other side of the cassette and then stops.
Both sides of the cassette indefinitely until
you press stop.
you press stop.
Selecting the Cassette Playback Mode
Your micro component system has three cassette playback
modes which enable you to listen to both sides of a cassette
automatically.
modes which enable you to listen to both sides of a cassette
automatically.
Press REV.MODE until the appropriate
symbol is displayed.
symbol is displayed.