MK Diamond mk 155779 mk-470 1 Betriebsanweisung

Ta b l e o f C o n t e n t s

Foryour safety, read all instructions!
These safety precautions should be followed at all times. Failure to follow these safety
precautions could result in injury to yourself and others. Safety is a combination of operator
common sense and alertness at all times when the saw is being used.

I M P O RTANT SAFETY INSTRUCTIONS FOR T H E MK-470 T I L E S AW

• KEEP GUARDS IN PLACE and in working order.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys

and adjusting wrenches are removed from tool before turning it on.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

• DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet

locations, or expose them to rain. Keep work area well lighted.

• KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.

• MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. Extension Cords Table 1 shows the correct size to use depending

on cord length and name plate ampere rating. If in doubt, use the next heavier gage. The

smaller the gage number, the heavier the cord.

• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught

in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

• ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact

resistant lenses, they are NOT safety glasses.

• SECURE WORK. Use clamps or a vice to hold work when practical. It‘s safer than using your hand and it frees both hands to

operate tool.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating

and changing accessories.

• DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

• USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper

accessories may cause risk of injury to persons.

• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped of if the cutting tool is unintentionally contacted.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to

determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged

should be properly repaired or replaced.

• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

• SAVE THESE INSTRUCTIONS.

General Safety Instructions

pg 1-2

Safety Messages
Hazard Symbols
Damage Prevention Messages
Safety Label Locations

Saw Features

pg 2-3

Motor
Cutting Head
Water Recirculation System

Unpacking and Preparation

pg 3

Initial Assembly

pg 3-5

Installing the Cutting Head
Installing the Blade
Installing the Water Pump
Electrical Requirements
Lockout Method

Sawing Operations

pg 5-6

General Cutting Guidelines
Table Markings

Maintenance

pg 6

Trouble Shooting

pg 7

Optional Accessories

pg 7

Parts Listing

pg 8-9

Exploded View

pg. 8

How to Order Repair Parts

back cover

Returned Merchandise Policy

back cover

Safety Messages

You CAN be injured if you don’t follow instructions.

Additional information as to the nature of the hazard is provided by the following Hazard S y m b o l s
which appear throughout the manual in conjunction with safety message alert symbols.

A safety message informs you about potential hazards that could hurt you or others. Each safety message is preceded by
one of the three words: Danger, Warning, or Caution.