Epson 61p Produktdatenblatt
Epson PowerLite 61p/81p Projector
6
-
Epson PowerLite 61p/81p Projector 6/04
Adjusting the Image Shape
The projector automatically corrects images that are distorted
when the projector is tilted up or down (up to a 15° tilt). The
Keystone window appears on the screen while the projector
makes the correction. If the projected image still isn’t
rectangular or has a “keystone” shape, do one or more of the
following:
when the projector is tilted up or down (up to a 15° tilt). The
Keystone window appears on the screen while the projector
makes the correction. If the projected image still isn’t
rectangular or has a “keystone” shape, do one or more of the
following:
❏ If your image looks like
or
, you’ve placed the
projector off to one side of the screen, at an angle. Move it
directly in front of the center of the screen, facing the screen
squarely.
directly in front of the center of the screen, facing the screen
squarely.
❏ If your image looks like
or
, the Auto Keystone
feature may have been disabled or you may need to manually
adjust the keystone correction value. (Auto Keystone is not
available when you’re using ceiling or rear projection.)
Follow the directions below:
adjust the keystone correction value. (Auto Keystone is not
available when you’re using ceiling or rear projection.)
Follow the directions below:
❏ To turn on Auto Keystone, press the
Menu
button on
the projetor or remote control. Use the
pointer button
on the remote control (or the arrow buttons on the
projector) to select the
projector) to select the
Setting
menu, then press
Enter
. If
Auto Keystone
is
OFF
, highlight this option and press
Enter
. Select
ON
in the Auto Keystone window that
appears and press
Enter
to save your changes. Exit the
menu by pressing the
Menu
button.
❏ To manually adjust the keystone correction value, press
the
or
button on the projector to correct the
shape of the image. After correction, your image will be
slightly smaller.
slightly smaller.
You can also make keystone adjustments using the projector’s
Setting menu.
Setting menu.
Adjusting the Brightness
The brightness of an image depends on the source you are
projecting and the amount of light in the room. If the image is
too bright or not bright enough, do one of the following:
projecting and the amount of light in the room. If the image is
too bright or not bright enough, do one of the following:
❏ Change the
Brightness
setting in the Image menu.
❏ Select
Low
or
High
for the
Brightness Control
option in
the Setting menu. Low brightness mode extends the life of
the lamp and decreases the fan noise.
the lamp and decreases the fan noise.
Adjusting the Color Mode
You may want to adjust the color mode to select a setting
that is appropriate for the image you’re projecting and the
environment in which you’re projecting it.
that is appropriate for the image you’re projecting and the
environment in which you’re projecting it.
If you’re projecting computer or RGB video images, the default
color mode is
color mode is
Presentation
, which is appropriate for
presentations in bright rooms. For other images, the default
color mode is
color mode is
Dynamic
, which optimizes video images using
natural colors.
The following table lists the available color modes.
To change the color mode, press the
Color Mode
button on
the remote control until you see the mode you want. The
currently selected setting appears in the upper right corner of
the screen. You can also use the projector menu system to select
the Color Mode in the Image menu.
currently selected setting appears in the upper right corner of
the screen. You can also use the projector menu system to select
the Color Mode in the Image menu.
Correcting Computer Images
If you’ve connected a computer and the image doesn’t look
right, or it doesn’t fit properly on the screen, press the
right, or it doesn’t fit properly on the screen, press the
Auto
button on the remote control. This automatically resets the
projector’s tracking, sync, resolution, and position settings. You
must be projecting an image for this button to have any effect.
Additionally, if the
projector’s tracking, sync, resolution, and position settings. You
must be projecting an image for this button to have any effect.
Additionally, if the
Auto Setup
option in the Signal menu is set
to
OFF
, the Auto function will not work.
Color mode
Description
sRGB
Use when projecting computer images
conforming to the sRGB color standard (the
default setting when projecting from a computer
with analog video).
conforming to the sRGB color standard (the
default setting when projecting from a computer
with analog video).
Dynamic
Best for projecting movies with vivid color in
bright rooms.
bright rooms.
Presentation
Use when you’re projecting a presentation in a
bright room.
bright room.
Theater
Use when projecting movies in a dark room.
Living Room
Best for playing video games or watching TV in a
bright room.
bright room.
Blackboard
Choose this fixed color mode when you need to
project against a green blackboard.
project against a green blackboard.