Heartland hcdwis Betriebsanweisung
25
Option 2: Power supply cord method:
NOTE: A mating, three prong, ground-type wall receptacle is
required in a cabinet next to the dishwasher opening.
1. Drill a 1-1/2” (3.8
cm) hole in the cabinet
rear or side. Preferred
and optional locations
are shown.
2. Wood cabinet: Sand
hole until smooth.
Metal cabinet: Cover
hole with grommet (Part
No. 302797) included with power supply cord kit.
NOTE: A mating, three prong, ground-type wall receptacle is
required in a cabinet next to the dishwasher opening.
1. Drill a 1-1/2” (3.8
cm) hole in the cabinet
rear or side. Preferred
and optional locations
are shown.
2. Wood cabinet: Sand
hole until smooth.
Metal cabinet: Cover
hole with grommet (Part
No. 302797) included with power supply cord kit.
Install the water line
Helpful Tip: Routing the water line through the left side of cabinet
opening will make water connection easier.
1. Drill a minimum 1/2” (1.3 cm) hole in the cabinet side, rear or
floor. Preferred and optional locations are shown.
opening will make water connection easier.
1. Drill a minimum 1/2” (1.3 cm) hole in the cabinet side, rear or
floor. Preferred and optional locations are shown.
2. Measure overall length of
copper tubing required.
3. Attach copper tubing to
the water line with a manual
shutoff valve.
4. Slowly feed copper tubing
through hole in cabinet.
Copper tubing will bend and kink easily, so be gentle. The copper
tubing should be far enough into the cabinet opening to connect it
to dishwasher inlet on the front left of the dishwasher.
5. Turn water shutoff valve to “ON” position. Flush water into a
shallow pan to get rid of particles that may clog the inlet valve.
6. Turn shutoff valve to “OFF” position.
copper tubing required.
3. Attach copper tubing to
the water line with a manual
shutoff valve.
4. Slowly feed copper tubing
through hole in cabinet.
Copper tubing will bend and kink easily, so be gentle. The copper
tubing should be far enough into the cabinet opening to connect it
to dishwasher inlet on the front left of the dishwasher.
5. Turn water shutoff valve to “ON” position. Flush water into a
shallow pan to get rid of particles that may clog the inlet valve.
6. Turn shutoff valve to “OFF” position.
Install the drain hose
IMPORTANT:
Always use a new drain hose.
1. Drill a 1-1/2” (3.8 cm)
diameter hole in cabinet
wall or floor on the side of
the opening closest to the
sink.
2. Connect drain hose to
waste tee or waste disposer using one of the following methods:
• Option 1, Waste disposer – with air gap
• Option 2, No waste disposer – with air gap
• Option 3, Waste disposer – no air gap*
• Option 4, No waste disposer – no air gap*
diameter hole in cabinet
wall or floor on the side of
the opening closest to the
sink.
2. Connect drain hose to
waste tee or waste disposer using one of the following methods:
• Option 1, Waste disposer – with air gap
• Option 2, No waste disposer – with air gap
• Option 3, Waste disposer – no air gap*
• Option 4, No waste disposer – no air gap*
*an air gap is recommended
Helpful Tip:To reduce the vibration of the hose, keep the hose away
from the floor and the edge of the hole where it passes through the
cabinet.
from the floor and the edge of the hole where it passes through the
cabinet.
Option 1:Waste disposer – with air gap:
1. Remove the disposer knockout plug. Cut end of drain hose if
needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the
drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screw-type clamps*
to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20” (50.8
cm) above the floor where dishwasher will be installed.
1. Remove the disposer knockout plug. Cut end of drain hose if
needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the
drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screw-type clamps*
to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20” (50.8
cm) above the floor where dishwasher will be installed.
4. Insert drain hose
through hole cut in
cabinet to the front center
of opening where drain
connection will be made.
through hole cut in
cabinet to the front center
of opening where drain
connection will be made.
* Parts available from local
plumbing supply stores
preferred
locations
optional
locations
optional
locations
preferred
locations
copper
tubing
drain
hose
large
spring-type
clamp
air gap
rubber hose
connector
disposer
inlet
drain trap
drain hose –
cut here if needed
spring or
screw-type
clamps
drain hose