Heartland hcdwis Betriebsanweisung
27
Prepare dishwasher
1. Put corner posts from packaging behind dishwasher. Grasp sides
of dishwasher door frame and put dishwasher on its back, resting on
top of the corner posts.
2. Remove two screws attaching access panel and lower panel
to dishwasher using a 1/4” hex socket, nut driver or Phillips
screwdriver.
of dishwasher door frame and put dishwasher on its back, resting on
top of the corner posts.
2. Remove two screws attaching access panel and lower panel
to dishwasher using a 1/4” hex socket, nut driver or Phillips
screwdriver.
3. Remove panels and set panels
aside on a protective surface.
4. Check that grounding clip is
attached to the lower panel.
5. Apply Teflon® tape or pipe joint
compound to 90° elbow fitting
and connect fitting to water inlet valve.
6. Tighten elbow until snug, and be sure that it faces to the rear.
aside on a protective surface.
4. Check that grounding clip is
attached to the lower panel.
5. Apply Teflon® tape or pipe joint
compound to 90° elbow fitting
and connect fitting to water inlet valve.
6. Tighten elbow until snug, and be sure that it faces to the rear.
7. Remove terminal box cover.
– If you are direct wiring: install a U.L.-listed/CSAcertified clamp
connector to the terminal box. If using conduit, use a U.L.-listed/
CSA-certified conduit connector.
– If you are installing a power supply cord kit, do so now, following
kit instructions.
– If you are direct wiring: install a U.L.-listed/CSAcertified clamp
connector to the terminal box. If using conduit, use a U.L.-listed/
CSA-certified conduit connector.
– If you are installing a power supply cord kit, do so now, following
kit instructions.
Helpful Tip:
Put cardboard under dishwasher until it is installed
in cabinet opening. The cardboard will help protect floor covering
during installation.
8. Measure height of cabinet opening from
underside of countertop to floor where
dishwasher will be installed (you need the
lowest point). Check chart for that height
opening.
during installation.
8. Measure height of cabinet opening from
underside of countertop to floor where
dishwasher will be installed (you need the
lowest point). Check chart for that height
opening.
9. Turn both front leveler legs to the same
height.
If the minimum cutout height is less than 34”
(86.4 cm), the rear wheels can be removed
for additional clearance. This will allow the
dishwasher to fit into a 33-7/8” (86 cm)
high cutout, but the dishwasher will be more
difficult to move into position. If the wheels are removed, protect
the floor when moving the dishwasher.
height.
If the minimum cutout height is less than 34”
(86.4 cm), the rear wheels can be removed
for additional clearance. This will allow the
dishwasher to fit into a 33-7/8” (86 cm)
high cutout, but the dishwasher will be more
difficult to move into position. If the wheels are removed, protect
the floor when moving the dishwasher.
If you have built-up floors
1. Measure height of opening from
underside of countertop to built-
up floor. If the height is at least
33-3/4” (85.7 cm), the dishwasher
will fit into the opening without
modification to the
countertop or flooring.
2. Put wheels in position 1 and
turn the front leveler legs up all
the way.
underside of countertop to built-
up floor. If the height is at least
33-3/4” (85.7 cm), the dishwasher
will fit into the opening without
modification to the
countertop or flooring.
2. Put wheels in position 1 and
turn the front leveler legs up all
the way.
3
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury
lower
panel
access
panel
grounding
clip
water inlet valve
elbow
ADVERTENCIA
AVERTISSEMENT
dishwasher wires
cable clamp
connector
terminal
box cover
1
2
3
2
3
wheel
1
2
3
2
3
10
5
0
0
Number of
turns on
front leg
Wheel
position
34" (86.4 cm)
34-1/4" (87 cm)
34-1/2" (87.6 cm)
34-1/4" (87 cm)
34-1/2" (87.6 cm)
Minimum
cutout height
front leg
shim
33-3/4"
(85.7 cm)
min.
countertop
built-up
floor