LG F1403FDS6 Benutzeranleitung

n

o

it

u

l

o

S

e

s

u

a

C

 

e

l

b

i

s

s

o

P

m

o

t

p

m

y

S

• Water supply is not adequate in area

• Water supply taps are not completely open.

• Water inlet hose(s) are kinked.

• The filter of the inlet hose(s) are clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

• Load is too small.

• Load is out of balance.

• The appliance has an unbalance detection

and correction system. If individual heavy

articles are loaded (ex. bath mat, both robe,

etc.), this system may stop spinning or even

interrupt the spin cycle altogether. 

• If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to

balance the load and repeat the spin cycle.

• Is the door opened or not

completely closed?

• Water overfills due to the faulty water

valve.

• Water level sensor has malfunctioned.

• Over load in motor.

• Water leaks

• The washer experienced a power failure.

Check another tap in the house.

Fully open tap.

Straighten hose(s).

Check the filter of the inlet hose(s).

Clean and straighten the drain hose.

Clean the drain filter.

For more detailed information, 

please refer to “Cleaning the drain pump filter” 

  

Add 1 or 2 similar items to help 

balance the load.

Rearrange load to allow proper 

spinning

Close the door completely.

If  “       ”is not released, call for service.

Unplug the power plug and call for service.

Close the water tap.

Unplug the power plug.

Call for service.

Call for service.

Restart the cycle.

• Heimservice zur Einführung in die Benutzung des Geräts.
• Wenn das Gerät an eine Spannung angeschlossen ist, die nicht mit der auf dem

Nennleistungsschild angegebenen übereinstimmt. 

• Wenn die Störung durch Unfälle, Vernachlässigung, Missbrauch oder höhere Gewalt

verursacht wird.

• Wenn die Störung durch unsachgemäße Benutzung des Geräts oder Nichtbeachtung

der Bedienungsanleitung verursacht wird.

• Die Gebrauchsanweisung für das Gerät zur Verfügung stellen oder die Einstellungen

des Geräts ändern.

• Wenn die Störung durch Schädlinge wie Ratten oder Kakerlaken etc. verursacht wird.
• Normale Geräusche oder Vibrationen z. B. das Geräusch von ablaufendem Wasser,

Drehgeräusche oder Pieptöne während der Erwärmung.

• Die Installation korrigieren, das Gerät nivellieren oder den Abfluss einstellen.
• Normale Wartung, wie sie im Benutzerhandbuch empfohlen wird.
• Entfernung von Fremdkörpern wie Sand, Nägeln, BH-Bügeln, Knöpfen etc. aus der

Maschine sowie aus der Pumpe und dem Einlassfilter.

• Sicherungen ersetzen oder die elektrischen Anschlüsse oder Rohrleitungen korrigieren.
• Korrektur von unbefugten Reparaturen. 
• Schäden an persönlichem Eigentum, die direkt oder indirekt durch Defekte dieses

Geräts verursacht werden.

• Wenn dieses Gerät zu kommerziellen Zwecken benutzt wird, steht es nicht unter Garantie. 

(Beispiel: öffentliche Orte wie Toiletten, Hotels, Fitness-Center, Pensionen) 

1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers

auf einem Produkt angebracht ist, unterliegt dieses Produkt
der europäischen Richtlinie 2002/96/EC.

2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom

Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt
werden.

3. Mit der ordnungsgemäßen Entsorgung des alten Geräts

vermeiden Sie Umweltschäden und eine Gefährdung der
persönlichen Gesundheit.

4. Weitere Informationen zur Entsorgung des alten Geräts

erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt
oder in dem Geschäft, wo Sie das Produkt erworben haben.  

. Die 4 Schrauben lösen und die

Gummipfropfen etwas drehen, um sie

zusammen mit den Schrauben abzunehmen.

Die 4 Schrauben und den Schraubenschlüssel

für späteren Gebrauch aufbewahren.

• Die Transportsicherungsschrauben müssen vor

jedem Transport des Geräts wieder angebracht

werden.

. Die Schraubenbohrungen mit den

beiliegenden Kappen verschließen.

Schraubenschlüssel

 

Adjustable feet

60 - 100 cm

@

N

E

L

N

E

L

N

F1403FDS(1~9)

WD-14988FDS

Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating 

instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these 

operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before instal-

ling the appliance and putting it into operation.  

•  Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold

drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and
may lead to injuries, whereby the liability of the manufacturer will cease.

•  This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
•  Never modify the appliance on your own, as this is dangerous.
•  This appliance is heavy. Transporting with care.
•  Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
•  All installation work must be carried out by a qualified fitter or technician.
•  Have electrical connections done by a qualified electrician.
•  Never place the appliance on the power cord.
•  If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
•  Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect

by pulling the power cord. Never touch the plug with wet fingers or hands.

•  Do not overload the appliance.
•  Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
•  Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
•  Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
•  Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
•  Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.

Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.

•  Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances

(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.

•  Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been

used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in
the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.

•  Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas.

Such materials may cause fire or explosion. Never use combustible detergents.

•  Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
•  After washing, keep the drum door open to protect the door seal.
•  Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
•  Animals and children may get into the washing machine. So always check the appliance before using it.
•  During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
•  Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
•  The product should be serviced and repaired only by the authorised customer service using original replacement parts.
•  When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
•  When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
•   If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
•   The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
•  Keep all washing powder and detergents away from children. Danger of poisoning

Before use please read carefully the safety instructions!

Thank you for buying an LG fully automatic washing machine.

Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.

Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.

•  The appliance is fitted with transit bolts to prevent internal  

damage during transport. 

Be careful, heavy load!

•  Packing and all transit bolts must be removed before using  

the washing machine. 

•  When unpacking the base, be sure to remove the additional 

packing support in the middle of the base packing.

Store original packing for future move.

Dispose of packing material according to local regulations.

Unscrew the 4 bolts 

using the spanner 

supplied.

Level floor: Permissible floor gradient under entire washing machine 

is 1˚ . 

Power socket: Must be within 100 cm of either side of location of 

washing machine. Do not overload the socket with more than one 

appliance. 

  

Additional Clearance: For wall, floor and door space is needed. 

(10cm: rear / 2cm:right & left side). Do not place or store laundry pro-

ducts on top of the washing machine at any times. They can damage 

the finish or controls of the machine.

•   Two rubber seals are supplied with the water inlet 

hoses. They are used for preventing water leaks. 

•   Make sure the connection to taps is tight enough. 
•   Periodically check the condition of the hose and 

replace the hose if necessary. 

•   Make sure that there is no kink on the hose and 

that it is not crushed. 

When your washing machine has two valves: 
•   The inlet hose with the red connector is for the hot 

water tap. 

•   If the washing machine has two valves, power 

saving is achieved through using hot valve.

Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)

Don’t strip or crossthread when connecting inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression 

device should be installed.

•  The drain hose should not be placed higher than 100 cm above the floor. 

•  Proper securing of the drain hose will protect the floor from damage due to any water leakage. 

•  If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.

•  Proper level-adjustment of the washing ma-

chine prevents excessive noise and vibration. 

Install the appliance on a solid and level floor 

surface, preferably in a corner of the room.  

•  If the floor is uneven, adjust feet as required. 

(Do not insert pieces of wood etc. under the 

feet). Make sure that all four feet are stable 

and resting on the floor. Then check that 

the appliance is perfectly level. (Use a spirit 

level).

Rattling and clanking noise 

Extraneous objects such as coins or safety pins maybe in drum or pump.

Thumping sound 

Heavy wash loads may produce a thumping sound. This is usually normal.

Vibrating noise 

Have all transit bolts and packing been removed?

Water leaks. 

Check and tighten hose connections. Unclog drain pipe. 

   

Contact plumber if necessary.

Excessive suds 

Too much detergent or unsuitable detergent.

Washing machine does not start 

Power cord may not be plugged in or connection may be loose.

Washing machine won’t spin 

Check that the door is firmly shut.

Door does not open 

Once started, the door can not be opened for safety reasons.

   

Wait one or two minutes before opening the door to allow the electric

   

locking mechanism time to release.

To prevent internal dama-

ge during transport, the 

special 4 bolts are locked. 

If they are not removed, it 

may cause heavy vibrati-

on, noise and machine to 

malfunction.

If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional 

type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting 

the tap into the adaptor.

i

For the U.K. customer

CUSTOMER SERVICES Tel. : 0870 - 873 - LGLG (5454) Fax. : 0870 - 872 - 7337

LGEUK SERVICE WEB-SITE : http://uk.lge.com

i

•  When this crossed-out wheeled bin symbol is attached to a product it means the product is covered

by European Directive 2002/96/EC.

•  All electrical and electronic products should be disposed of separately from municipal waste stream

via designated collection facilities appointed by the government or the local authorities.

•  The correct disposal of your old appliance will help prevent potential adverse consequences for the

environment and human health.

•  For more detailed information about disposal of your old appliance, please contact your city office,

waste disposal service or the shop where you purchased the product.

The hose supplied with the machine must be used. Old hoses may not be reused

Close the holes with 

the caps supplied.

Remove the 4 bolts 

along with the rubber

bungs by slightly 

twisting the bung.

P/No. :MFL38868794