Sony MEX-BT38UW Handbuch
33
MP3/WMA/AAC files take longer to play back
than others.
than others.
The following discs take a longer time to start
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in Multi Session.
– a disc to which data can be added.
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in Multi Session.
– a disc to which data can be added.
The display items do not scroll.
• For discs with very many characters, those may not
scroll.
• “A.SCRL” is set to “OFF.”
t Set “A.SCRL-ON” (page 26).
t Press and hold (DSPL) (SCRL).
t Press and hold (DSPL) (SCRL).
The sound skips.
• Installation is not correct.
t Install the unit at an angle of less than 45° in a
sturdy part of the car.
• Defective or dirty disc.
The operation buttons do not function.
The disc will not eject.
The disc will not eject.
Press the RESET button (page 6).
USB playback
You cannot play back items via a USB hub.
This unit cannot recognize USB devices via a USB
hub.
hub.
Cannot play back items.
A USB device does not work.
t Reconnect it.
t Reconnect it.
The USB device takes longer to play back.
The USB device contains files with a complicated tree
structure.
structure.
A beep sounds.
During playback, the USB device has been
disconnected.
t Before disconnecting a USB device, make sure to
disconnected.
t Before disconnecting a USB device, make sure to
stop playback first for data protection.
The sound is intermittent.
The sound may be intermittent at a high-bit-rate of
more than 320 kbps.
more than 320 kbps.
Bluetooth function
The connecting device cannot detect this unit.
• Before the pairing is made, set this unit to pairing
standby mode.
• While connected to a Bluetooth device, this unit
cannot be detected from another device. Disconnect
the current connection and search for this unit from
another device.
the current connection and search for this unit from
another device.
• When the device pairing is made, set the Bluetooth
signal output to on (page 23).
Connection is not possible.
• Connect to this unit from a Bluetooth device or vice
versa. The connection is controlled from one side
(this unit or Bluetooth device), but not both.
(this unit or Bluetooth device), but not both.
• Check the pairing and connection procedures in the
manual of the other device, etc., and perform the
operation again.
operation again.
The talker’s voice volume is low.
Adjust the volume level.
A call partner says that the volume is too low
or high.
or high.
Adjust the volume accordingly using Mic Gain
adjustment (page 23).
adjustment (page 23).
Echo or noise occurs in phone call
conversations.
conversations.
• Lower the volume.
• If the ambient noise other than the phone call sound
• If the ambient noise other than the phone call sound
is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is loud,
shut the window. If the air conditioner is loud, lower
the air conditioner.
E.g.: If a window is open and road noise, etc., is loud,
shut the window. If the air conditioner is loud, lower
the air conditioner.
The phone is not connected.
When the Bluetooth audio is played back, the phone is
not connected even if you press
not connected even if you press
(handsfree).
t Connect from the phone.
The phone sound quality is poor.
Phone sound quality depends on reception conditions
of cellular phone.
t Move your car to a place where you can enhance
of cellular phone.
t Move your car to a place where you can enhance
the cellular phone’s signal if the reception is poor.
The volume of the connected audio device is
low (high).
low (high).
Volume level will differ depending on the audio
device.
t Adjust the volume of the connected audio device or
device.
t Adjust the volume of the connected audio device or
this unit.
The sound skips during playback of a
Bluetooth audio device.
Bluetooth audio device.
• Reduce the distance between the unit and the
Bluetooth audio device.
• If the Bluetooth audio device is stored in a case
which interrupts the signal, remove the audio device
from the case while using.
from the case while using.
• Several Bluetooth devices or other devices which
emit radio waves are used nearby.
t Turn off the other devices.
t Increase the distance from the other devices.
t Increase the distance from the other devices.
• The playback sound stops momentarily when the
connection between this unit and the cellular phone is
being made. This is not a malfunction.
being made. This is not a malfunction.
The connected Bluetooth audio device cannot
be controlled.
be controlled.
Check that the connected Bluetooth audio device
supports AVRCP.
supports AVRCP.
Some functions do not work.
Check if the connecting device supports the functions
in question.
in question.
A call is answered unintentionally.
The connecting phone is set to answer a call
automatically.
automatically.
No sound is output from the car speakers
during handsfree call.
during handsfree call.
If the sound is output from the cellular phone, set the
cellular phone to output the sound from the car
speakers.
cellular phone to output the sound from the car
speakers.
continue to next page
t